Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
It is the operator's responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine. Workplace Inspection Be aware of and avoid the following hazardous situations: · drop-offs or holes · bumps, floor obstructions or debris · sloped surfaces · unstable or slippery surfaces · overhead obstructions and high voltage conductors · hazardous locations · inadequate surface support to withstand all load forces imposed by the machine · wind and weather conditions · the presence of unauthorized personnel · other possible unsafe conditions Genie Super Hoist Part No. 82297 Fourth Edition • Second Printing Operator’s Manual Operating Instructions Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. 5 Only use the machine as it was intended. Fundamentals The Operating Instructions section provides instructions for each aspect of machine operation. It is the operator's responsibility to follow all the safety rules and instructions in the operator's manual. Using the machine for anything other than lifting material is unsafe. If more than one operator is expected to use a machine at different times in the same work shift, each operator is expected to follow all safety rules and instructions in the operator's manual. That means every new operator should perform a pre- operation inspection, function tests and a workplace inspection before using the machine. Operating Instructions This machine is intended for use as a material lift only. When new, the machine may be stiff due to tight seals and packings. The machine will function smoother after use. The machine is heavily lubricated during manufacture to assure long lasting and smooth performance. Occasionally, excess oil may leak out of the quick disconnect plug at the base of the cylinder assembly. Take precautionary care to avoid lubricant spills on finished floors. Setup Follow the instructions listed in the Function Tests section. Platform Raise and Lower 1 Lock all four caster brakes. 2 Raise the platform by pressing the up button on the hand control. 3 Lower the platform by pressing the down button. Part No. 82297 Genie Super Hoist Operator’s Manual Fourth Edition • Second Printing OPERATING INSTRUCTIONS Manual Lowering 1 Open the manual dump valve on top of the hand control. Storage Instructions 1 Completely lower the platform. Close the CO2 tank valve by turning the handle clockwise. Remove the platform and CO2 tank. Disconnect the hose and hand control and coil it on the clips under the platform. 2 Support the cylinder assembly with one hand. With the other hand, release the nearest leg lock. Raise the leg and lock it in the storage position. Repeat this procedure for the other three legs. 3 Select a safe storage location that is weather protected and away from traffic. Preferably, store the machine standing up on its base to preserve smooth operation and prolong the life of the seals. Genie Super Hoist Part No. 82297 Fourth Edition • Second Printing Operator’s Manual Maintenance Schedule Maintenance Schedule Daily Inspect and, if necessary, tighten the following components: fittings, hoses, fasteners. Inspect the leg locks to be sure that they move freely and the springs function properly through their entire range of motion. Inspect the casters and the caster brakes. Monthly Visually inspect the felt wipers. Remove debris and clean as necessary. Part No. 82297 Genie Super Hoist Operator’s Manual Fourth Edition • Second Printing Decals Decal Inspection Use the pictures on this page to verify that all decals are legible and in place. Below is a numerical list with quantities and descriptions. Part No. Description Quantity 32305 Warning - Machine Safety 1 38149 Label - Patents 1 52980 Cosmetic - Genie Super Hoist 1 82960 Warning - Machine Safety 1 32305 or 82960 38149 52980 Serial Plate Genie Super Hoist Part No. 82297 Fourth Edition • Second Printing Operator’s Manual Specifications Genie Super Hoist 3.8 Genie Super Hoist 5.6 Height 41 in 1.04 m Height 54 in 1.37 m Platform length 19 in 48 cm Platform length 19 in 48 cm Platform width 24 in 61 cm Platform width 24 in 61 cm Base width, corner to corner 53 in 1.35 m Base width, corner to corner 53 in 1.35 m Load capacity 300 lbs 136 kg Load capacity 250 lbs 113 kg Lifting height 12 ft 55/8 in 3.8 m Lifting height 18 ft 41/2 in 5.6 m Dimensions for storage/transport 14 x 14 x 391/2 in 36 cm x 36 cm x 1 m Dimensions for storage/transport 14 x 14 x 391/2 in 36 cm x 36 cm x 1 m Weight 64 lbs 29 kg Weight 69 lbs 31 kg Recommended psi 85 psi 5.86 bar Recommended psi 85 psi 5.86 bar Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Part No. 82297 Genie Sup...