Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Intended Use The Swift LT channels airflow noninvasively to a patient from a positive airway pressure device such as a continuous positive airway pressure (CPAP) or bilevel system. The Swift LT is: • • to be used by adult patients (> 66 lb/30 kg) for whom positive airway pressure has been prescribed • • intended for single-patient re-use in the home environment and multipatient re-use in the hospital/institutional environment. Using the Swift LT When using the Swift LT with ResMed flow generators that have mask setting options, if available select ‘SWIFT’; otherwise select ‘MIRAGE’ as the mask option. Notes: • • The Swift LT is not compatible for use with ResMed AutoSet CS™ 2 and VPAP™ Adapt SV devices. • • SmartStop may not operate effectively when using Swift LT with some flow generators that have this feature. • • If you experience nasal dryness or irritation, use of a humidifier is recommended. Rx Only 2 Parts of the Swift LT & Ordering Information Complete system 60560 (includes small, medium and large pillows) Frame system (pillows, frame, short tube assembly) S* 60582; M* 60583; L* 60584. Frame assembly (frame, short tube assembly) 60581 S* Small; M* Medium; L* Large. Elbow Short tube assembly 60577 Frame 60575 Swivel Pillows 60571 (S*) 60572 (M*) 60573 (L*) Plastic tube retainer 60586 Top buckle 60579 (1) 60580 (10) Headgear assembly 60578 Back buckle 60558 (1) 60559 (10) Velcro™ tube retainer (sold separately) 60557 3 English Fitting your Swift LT B A 1 2 3 (A) Hold the pillows at your nose; (B) pull the headgear over your head. Adjust top straps (overtightening may cause excess pressure on your nose). Adjust each end of the backstrap (overtightening may cause excess pressure on upper lip). 4 5 6 Rotate frame to adjust pillow angle to ensure it sits comfortably. Connect the short tube to the flow generator’s air tubing. The Swift LT is now fitted and ready for use. Headgear should sit midway between ear and eye. Using the Plastic Tube Retainer (Optional) 1 Swift LT 2 3 Push tube retainer into buckle. Clip either short tube or air tubing to tube retainer. When using the tube retainer, the tubing can be positioned to either side of your face or centered. If the mask pulls on your nose, increase length of tube between mask and tube retainer. 4 Disassembling your Swift LT 1 Swift LT 2 Detach air tubing from short tube. Remove headgear from frame. 3 4 Remove pillows from frame. Remove elbow from frame. Cleaning your Swift LT in the home Notes: • • The nasal pillows system and headgear should be cleaned by handwashing. • • The headgear may be washed without being disassembled. WARNING Do not use aromatic-based solutions or scented oils (eg, eucalyptus or essential oils), bleach, alcohol or products that smell strongly (eg, citrus) to clean any of the system’s components. Residual vapours from these solutions can be inhaled if not rinsed thoroughly. They may also damage the system, causing cracks. 5 English CAUTION If any visible deterioration of a system component is apparent (cracking, crazing, tears etc.), the component should be discarded and replaced. Daily/After Each Use Handwash the separated mask components (excluding headgear) by gently rubbing in warm (approx. 86°F/30°C) water using mild soap for one minute. Rinse all components well with drinking quality water and allow them to air dry out of direct sunlight. Weekly Handwash the headgear and tube retainer in warm (approx. 86°F/30°C) water using mild soap. Rinse well and allow them to air dry out of direct sunlight. Reprocessing your Swift LT between Patients The Nasal Pillows System should be reprocessed when used between patients. Cleaning, disinfection and sterilization instructions are available from the ResMed website, If you do not have Internet access, please contact your ResMed representative. Storage Ensure that your Swift LT is thoroughly clean and dry before storing it for any length of time. Store the mask in a cool dry place out of direct sunlight. Disposal The Swift LT does not contain any hazardous substances and may be disposed of with your normal household refuse. Limited Warranty ResMed warrants that your ResMed system, including its components: frame, pillow sleeve, headgear, tubing and other accessories (“Product”) shall be free from defects in material and workmanship for a period of ninety (90) days from the date of purchase by the initial consumer. For further details refer to the Warranty. 6 Reassembling your Swift LT 1 2 3 Insert elbow into frame. Align pillows with frame. Push pillows firmly into frame. Ensure top and bottom retention tabs slot into place. 4 5 Check positioning markers on pillows and headgear are on the same side. Slide left and right headgear stability arms onto frame. Ensure inner wall of pillows is in correct position. If not, squeeze pillow sides to release inner walls. Reassembling the headgear S wif t L T B A A B Lay out the headgear as shown, writing f...