Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
D3 is pre-filled with fluid grease. 1. Lift off the cover to the operator. 2. Remove the control card and battery so that you can gain access to the filler plug. 3. Unscrew the cap and pour in the oil provided For transport purposes this unit has been supplied with oil in a separate sealed container. Oil Specifications: GRADE: 75W90 Qty: 75ml IMPORTANT 36 38 34 30 31 32 33 35 37 IO L LLEVEWARNING! (D5/A5 ONLY) Fill with oil prior to running gearbox. NB. D3 is pre-filled with fluid grease. 1. Lift off the cover to the operator. 2. Remove the control card and battery so that you can gain access to the filler plug. 3. Unscrew the cap and pour in the oil provided For transport purposes this unit has been supplied with oil in a separate sealed container. Oil Specifications: GRADE: 75W90 Qty: 75ml IMPORTANT 03 31 32 33 34 35 36 73 38 MAJOR COMPONENTS (TYPICAL D5 SHOWN) - COVER - CONTROLLER (CP80 FOR D3/D5; CP81 FOR A5) - MOTOR (12V DC FOR D3/D5; 220V AC FOR A5) - BATTERY (12V DC, 7A/H-D3/D5 ONLY) (OR PSU1/2, IF FITTED) - CHARGER TRANSFORMER/POWER SUPPLY (CP84E for D3/D5 or CP83E for A5) (NOT FITTED WHEN PSU1/2 IS USED). - GEARBOX CASING - INTERNAL LIMIT SWITCH (DOSS) - MANUAL RELEASE THUMBWHEEL - LOCKABLE ACCESS DOOR 1 TABLE 1 START (kgF) RUN (kgF) GATE MASS (kg) D3 25 12 300 D5 60 20 500 D5 Light Industrial 16* 16* 500 A5 22 22 500 *LIMITED BY CAPACITY OF PSU 2 ANTI-LIFT BRACKETS - Guide rollers 39 must ensure that the gate is held vertically. - Fit suitable anti-lift brackets 42. The gap 40 should be <5mm to ensure the gate cannot be lifted off the motor pinion. - For improved safety fit additional support post 39 to prevent gate from falling over if guide rollers 41 fail. 3 D5 100 120 A5 100 81 67 80 Duty Cycle ( % ) * 56 48 41 36 Duty Cycle ( % ) 60 40 20 6 81012141618 20 Duty Cycle ( % ) 2224262830 25 5 30 15 20 25 30 Pull ( kgf ) Time (hrs) A5 with FAN 120 100 80 60 40 20 0 0 5 15 20 Time (hrs) DUTY CYCLE CURVES - FOR THE WARRANTY TO BE VALID, ENSURE THAT THE DUTY CYCLE IS NOT EXCEEDED FOR THE PARTICULAR MOTOR BEING USED. * - DUTY CYCLE IS SUBJECT TO BATTERY AND CHARGER SIZE. 4 9 8 10 6 5 7 3 4 11 2 9 8 10 6 5 7 3 4 11 2 RECOMMENDED INSTALLATION AND CABLE THICKNESS REQUIREMENTS† 3 2 4 5 6 7 8 9 10 11 - LOCAL ISOLATOR - MAINS SUPPLY (min 0.5mm. ‡, 2 CORE + EARTH) - INTERCOM AND STATUS SIGNALING TO HOUSE (0.2mm., *n1 + 6 CORE) - INTERCOM TO GATE STATION (0.2mm., #n2 CORES) - PILLAR LIGHTS (0.5mm., 2 CORE + EARTH) - RADIO RECEIVER (0.2mm., 3 CORE) - PEDESTRIAN KEYSWITCH (0.2mm., 2 CORE) - INFRA RED BEAM (0.2mm., 3 CORE) - FREE EXIT LOOP (1.5mm., multi stranded cable) - FREE EXIT CONTACT (0.2mm., 2 CORE) † For cable types to be used (e.g. SWA, Cabtyre, Intercom cable etc.) consult your municipal authority for details. * n1 = NUMBER OF CORES REQUIRED BY INTERCOM # n2 = NUMBER OF CORES REQUIRED BY INTERCOM ‡ sufficient for motor only, increase to suit total load if pillar lights are fitted 5 MECHANICAL MOUNTING DETAILS Option 1 -Bolt down onto concrete plinth -Ensure motor does not protrude into drive-way install baseplate with centre line 250mm off pillar centre. -Position baseplate (43) with centre of single support stud (45) 105mm from edge of gate (46). (This dimension assumes centre line of rack (47) is 20mm from edge of gate). -Using the baseplate as a template mark and drill the 4 mounting holes into the concrete for the four M10 x 95 expansion studs. -Use two M12 plated nuts per expansion stud as spacers below the foundation plate. -Secure the baseplate to the expansion studs using one M10 washer and nut per expansion stud. 105mm 20mm 4545 4343 4747 4646 C L 6 7 2 m 50m L C M10 Nut Use two M12 plated nuts as spacers. M10 Washer M10 x 95 expansion stud Existing concrete plinth 105mm 20mm 4545 4343 4444 4343 m250m 4444 LC 04m0m400mm 300mm MECHANICAL MOUNTING DETAILS Option 2 -Set into concrete plinth 105mm 20mm 4545 4343 4444 4343 m250m 4444 LC 04m0m400mm 300mm MECHANICAL MOUNTING DETAILS Option 2 -Set into concrete plinth 4747 4646 C L -Ensure motor does not protrude into drive-way install baseplate with centre line 250mm off pillar centre. -Fasten concrete anchors (44) to the baseplate (43) using the M10x45 bolts provided. Ensure that the bolts are well tightened. -Position baseplate (43) with centre of single support stud (45) 105mm from edge of gate (46). (This dimension assumes centre line of rack (47) is 20mm from edge of gate). 8 PROVISION FOR CABLES - Ensure cables are fitted through base plate before concreting in place. - Remove knock-outs from gearbox to allow for cable entry. - Route cables in front of battery (D3/D5 motors) as shown above. - Seal cable entry holes with silicone sealer. 9 47 46 43 47 350 mm 30 mm 46 43 7 m m 53 52 54 51 54 7mm 53 52 54 51 54 GEARBOX MOUNTING DOWN DETAILS - Leave at least 7mm clearance between the lower gearbox nuts and the baseplate to allow for later adjustment. - Gearbox MUST be firmly located between top & bottom nuts and washers as shown at 54 . Use spring w...