Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
NO- 532 HIGH CAPACITY TRAILER FRAME & COVER MFG. NO. 531 VACUUM COLLECTOR ATTACH MENTS ROVING NOZZLE MFG. NO. 447 VACUUM COLLECTOR ADAPTER MFG. NO. 453 ACUUM COLLECTOR ADAPTER MFG. NO. 537 VACUUM COLLECTOR ADAPTER MFG. NO. 547 Mfrs. No. 533 LITHO !N U S A PACKING The Vacuum Collector is delivered complete in two cartons. The long carton contains: 2' Hoses The short carton contains: 1 - V.C. Blower Assembly 1 * Deflector 3 - Hose Clamps 1 - Flange - Hose 1 - Pack of Hardware Should any shortages of the above items occur, advise by stating the packers number listed on the green packing dip, part Dumber and description of Items missing. ASSEMBLY 1. The blower unit come? fully assembled. Attach the blower unit to the tfactor rear hitch by means of the pins and clips provided. 2. Prepare the rotary mower attachment for use with the vacuum collector by attaching the correct adapter kit. Example: See Figures 2 and 3. Note the bolt nearest the exhaust opening bas a spacer and flat washer under the attaching nut (Figure 2). Attach the carriage bolt for the exhaust cover (Figure 2) and secure the cover in position by means of the large wing nut assembly provided in adapter Ml {Figure 3). 3. Secure the large hose to the left side of the blower with the clamp, flange and hardware provided (Figure 4) and then place the other end at the large hose securely over the spout extension on the exhaust cover (Figure 3) of the adapter kit 4. Install deflector No. 123107 in the exhaust hole at the top of the blower housing with self-tapping screws. 5. Place the pulley on the shaft of the bevel gear housing. The new pulley will he secuied outboard of the P.T.O* pulley with the key and setscrew provided. (Figure 5). Figure 1 Figura 2 2 6. Place "V" belt (furnished with adapter kits) around ie previously installed pulley. Run other end around the ¿■ive pulley and idler pulley which are mounted oo the frame at blower. The spring on the idler pulley will auto* matically adjust belt tension. (FigureS). 7. Remove the pulley guard on the upper right side of the blower assembly and position the blower drive belt over the pulleys as shown (Figure 6). Adjust the belt tea* son as required. A space of approximately 3/4" should be between the set collar and guide bracket when engaged (Figure 6). Replace the pulley guard (Figure 7). Figure S Figure 7 Mfrs. NO. 531 HIGH CAPACITY TRAILER FRAME & COVER PACKING The High Capacity Trailer Frame & Cover Assembly is delivered complete in one carton. The carton contains: 1 • Canvas Cover 1 * Door Cover 1 ’ Pack of Hardware Should any shortages of the above items occur, advise by stating the packers number listed on the green packing dip, part number and description of items missing, ASSEMBLY Hie cart enclosure for the vacuum collector consists of 9 metal framework and a canvas cover, all of which fits on tbe dump cart body. 1. The canvas cover is completely assembled to th metal framework with the oxception of the upper hangs, brackets and the front catch. Z Unfold the canvas covcr assembly and secure the four comer braces with the hardware provided. See Figure 1. 3. Remove the upper hanger brackets from the hardware pack and assemble as shown in Figure 2. 4. Remove the catch assembly from the hardware pack and assemble as shown in Figure 3, The catch is secured with a locknut which should be tightened just enough to hold securely but still allow pivoting. 5. Secure the smaller sized hose to the outlet opening on top of the blower housing. The other end of the hose is positioned through the canvas sleeve at the upper front of the cart enclosure and secured in place by means of the strap and bucket See Figure 4. Figur« 2 ADJUSTMENT 1. To obtain maximum efficiency from the vacuum collector, it is recommended that ail assembly instructions be closely followed when mounting the vacuum collector to the tractor. A check should be made to insure the belts are in the correct location and have the proper tension. Too much tension on a belt will cause prematuro failure of the 1 belt. Not enough tension will cause the belt to slip andim-pair the operation of the vacuum collector. OPERATION 1. Be sure unit is properly adjusted and attached to tractor. 2. Inspect hoses, housing and fan assembly and remove grass clippings and material from vacuum collector after use. Bo sure the fan is tight on the bag shaft assembly. 3. In some operations it may be advisable to use a ground speed reduction kit on the tractor. Slowing the ground speed and maintaining £he fan speed will produce increased vacuum. 4. Insure mower is engaged and operate the tractor at 3/4 to full throttle. In extreme conditions it may be desirable to operate the tractor in first or second gear rather than in third gear. 5. In wet or extremely high grass, it may be necessary to pick up only half the mower width rather than the full width, to prevent the hoses from becoming clogged with grass. 6. When picking ...