Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
• Avoid accidental starting. Ensure the switch is in the off position before plugging tool into power outlet. Do not carry the power tool with your finger on the switch. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. 2 TOOL USE AND CARE • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative. • Disconnect the power from tool and place the switch in the locked or off position before making any adjustments, changing accessories, or storing power tools. Make sure blade has stopped. Such preventive safety measures reduce the risk of starting the power tool accidentally. • Secure work with clamps or a vise instead of your hand to hold work when practical. This safety precaution allows for proper tool operation using both hands. • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. • Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. • Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. • Keep guards in place and in working order. • Never leave tool running unattended. • Before drilling into walls, ceilings etc, ensure there are no concealed power cables or pipes in the cavity. • Always use the side handle; this gives you greater control if the accessory should become jammed. • Keep the cord clear of the accessory being used. Do not wrap the cord around your arm or wrist. • Get a good grip. Hold the tool by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own cord. • Use thick cushioned gloves and limit the exposure time by taking frequent breaks. Vibration caused by the hammer action may be harmful to your hands and arms. • When removing an accessory from the tool, avoid contact with skin and use proper protective gloves when grasping the bit or accessory. Accessories may be hot after prolonged use. WARNING! The use of any accessory or attachment, or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury. • Always wear eye protection and a dust mask, especially for dusty applications and when drilling / chiseling overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health complications. 3 OPERATION BEFORE ATTACHING OR REMOVING ANY ACCESSORIES BE SURE TO DISCONNECT THE HAMMER DRILL FROM THE POWER SUPPLY. 4 Fitting and changing tools (Fig.2) The device is equipped with a SDS-plus attachment system. • clean tools and grease with a thin layer of machine grease before fitting. • Pull back fastening sleeve (A, Fig.2) and hold. • Push and rotate the dust-free tool into the tool holder as far as it will go. The tool will lock automatically. • Check that it has locked by pulling the tool. Removing SDS-plus tool (Fig.3) Pull back fastening sleeve (A), hold and remove the tool. Starting work (Fig.1) Switching ON/OFF • switching on: Press the operating switch (3). • switching off: Press the operating switch (3) briefly and let go. 5 Handle attachment (Fig.4) For safety reasons, only use the hammer drill with handle attachment. You will be able to achieve a safe body position during operation by rotating the handle attachment. Loosen and turn the handle attachment in an counterclockwise direction. Then tighten the handle attachment. Depth stop (Fig.5) Loosen the handle attachment and place the straight part of the depth stop into the hole. Adjust the depth stop and re-tighten the handle attachment. Dust collection device (Fig. 6) Before doing any overhead hammer-drilling work, attach the dust-collecting cup over the drill bit. Drill Stop (Fig.8) • You can deactivate the drilling action of the hammer drill when using it for chiseling work. • Turn the lever selector (7) so that the mark “T” coincides with the arrow (a) on the machine case. • To reactivate the drilling action, the lever selector (8) has to be reset so that the mark (b) “I T” coincides with the arrow (a). Important...