Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
13. Keep your work area clean. Immediately remove split wood around the machine so you do not stumble over it. 14. Never move this machine while the engine is running. 15. This machine should not be towed on any street, highway or public road without checking the existing federal, state, or local vehicle requirements. Any licensing or modifications such as taillights, etc., needed to comply, is the sole responsibility of the purchaser. If a “Statement of Origin” is required in your state, see your local dealer. 16. Do not tow machine faster than 45mph. 17. See Transporting the Log Splitter section in this manual for proper towing instructions once all federal, local, or state requirements are met. Maintenance and Storage 1. Stop the engine, disconnect the spark plug and ground it against the engine before cleaning, or inspecting the machine. 2. Stop the engine and relieve hydraulic system pressure before repairing or adjusting fittings, hoses, tubing, or other system components. 3. To prevent fires, clean debris and chaff from the engine and muffler areas. If the engine is equipped with a spark arrester muffler, clean and inspect it regularly according to manufacturers instructions. Replace if damaged. 4. Periodically check that all nuts and bolts, hose clamps, and hydraulic fittings are tight to be sure equipment is in safe working condition. 5. Check all safety guards and shields to be sure they are in the proper position. Never operate with safety guards, shields, or other protective features removed. 6. The pressure relief valve is preset at the factory. Do not adjust the valve. 7. Never attempt to move this machine over hilly or uneven terrain without a tow vehicle or adequate help. 8. For your safety, replace all damaged or worn parts immediately with original equipment manufacturer’s (O.E.M.) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” 9. Do not alter this machine in any manner, alterations such as attaching a rope or extension to the control lever, or adding to the width or height of the wedge may result in personal injury. Your Responsibility Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Some of the safety labels are reproduced here. Always follow directions on safety labels found on your equipment. 4 5 SECTION 2: ASSEMBLING YOUR LOG SPLITTER Unpacking from Crate • Pry top, sides, and ends off the crate. Set panels aside to avoid tire puncture or personal injury. • Remove and discard plastic bag that covers unit. • Remove any loose parts if included with unit (i.e., operator’s manual, etc.) • Cut and remove straps which secure parts to bottom of crate. Unbolt any remaining parts which may be bolted to the bottom of the crate. Loose Parts 1. Reservoir Tank and Engine-Pump Assembly 2. Engine-Pump Assembly Hardware 3. Wedge, Beam and Cylinder Assembly 4. Tongue Assembly 5. Wheels 6. Hitch Assembly 7. Beam Support/Latch Bracket 8. Log Cradle Brackets and Hardware 9. Fenders 10. Adjustable Jack Stand Assembly 11. Tail Light Kit 12. Hub Cap (2) Figure 1 Before Assembling • Disconnect spark plug wire and ground against the engine to prevent unintended starting of the log splitter. To locate the spark plug, please refer to the engine manual, shipped seperately with the unit. Attaching Beam Support/Latch Bracket The beam support is already attached to the tongue before shipping. If not, follow instructions below: • Remove two hex bolts, lock washers, and hex nuts from the tongue. See Figure 2. • Place the beam support/latch bracket on the tongue and secure with the hardware just removed. Tighten securely. Figure 2 Attaching Jack Stand • Remove four hex bolts, lock washers, and hex nuts that secure jack stand mounting brackets to the jack stand. See Figure 3. • Place the jack stand halfway between beam support/latch bracket and end of tongue. Figure 3 WARNING: Use extreme caution while unpacking this machine. Some components are very heavy and will require extra people or mechanical handling equipment to move. Log Cradle Tail Light Kit Beam Support/ Latch Bracket Hitch Assembly Tongue Assembly Jack Stand Wheel & Fender Assembly Wedge, Beam & Cylinder Assembly Hex Bolts Lock Washer Tongue Hex Nut Beam Support/ Latch Bracket Hex Bolts Mounting Brackets Jack Stand Lock Washer Hex Nuts Tongue Lock Washer 6 • Insert hex bolts through top holes in jack stand mounting brackets and holes in jack stand. Secure with lock washers and hex nuts. See Figure 3. • Insert hex bolts through upper holes in the bottom of mounting brackets and jack stand. Secure with lock washers and hex nuts. See Figure 3. Hitch Assembly The hitch assembly is already attached to the tongue before shipping. If not, follow instructions below: • Remove the hardware from the hitch assembly and place the hitch on the end of the tongue. • Insert hex bolt thr...