Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
See figure 18. 2. Pull the inlet hose off the fitting at the beam. Using an adjustable wrench, remove the fitting from the beam. 3. Reach inside the end of the beam and pull out the strainer tube assembly. 4. Clean the strainer tube assembly and reassemble in reverse order. Reassemble the end plate. Refill oil reservoir with approximately 2-1/2 to 3 gallons of Dexron II automatic tarnsmission fluid as instructed in "Before Starting" under OPERATION section. CLAMPS ^neck the hose clamps on the bottom of the pump for proper tightness before each use. Hose clamps on the return hose should be checked once a season. CARBURETOR ADJUSTMENTS ▲ { WARNING J If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler. Refer to engine manual packed with your unit for carburetor adjustment information. TIRE PRESSURE Check sidewall of tire for manufacturer's maximum tire pressure. If this information does not appear on your tire, maximum tire pressure under any circumstances is 30 p.s.i. Equal tire pressure should be maintained on all tires. INSTALLATION OF TIRE TO RIM Ac warnIng *| The following procedure must be followed when removing or installing a tire to the rim. 1. Be sure rim is clean and rust free. 2. Lubricate both the tire and rim generously. 3. Never inflate to over 30 p.s.i. to seat beads. Excessive inflation pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. OFF-SEASON STORAGE If the machine is to be inoperative for a period longer than 30 days, prepare for storage as follows. 1. Clean the engine and the entire unit thoroughly. 2. Wipe the entire machine with an oiled rag to protect the surfaces. 3. Refer to the engine manual for correct engine storage instructions. The engine must be completely drained of fuel to prevent gum deposits from forming on essential carburetor parts, fuel lines and fuel tanks. 4. Store unit in a clean, dry area. NOTE When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially all moving parts. 11 IF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL NOTE: The engine is not under warranty by the log splitter manufacturer ... If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the "Yellow Pages" of your telephone book under " Engines — Gasoline”. Find It Fast In Tl ie Yellow I’ages ■^NOTE This instruction manual covers various models and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. *The hydraulic pump is one of two tvpes. As complete units, the two pumps are interchangeable (refer to parts list for part number). If it is necessary to determine the specific type of pump on your unit, refer to the illustrations below. ALLEN / HEAD SCREWS HEX HEAD^ ^ BOLTS BARNES PUMP FENIMER STONE PUMP 12 Models 642 and 645 PARTS LIST FOR MODELS 642 AND 645 LOG SPLITTERS Nef. MO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 710-0118 Hex Bolt 5/16-18 x .75" 44 13115 Ferrule Ass'y. Lg.* 45 712-0214 Hex Cent. L.-Nut 3/8-24 2 710-0168 Hex Bolt 3/8-16 x.60" Lg.* Thd. 3 712-0267 Hex Nut 5/16-18 Thd.* 46 720-0157 Grip-Black Vinyl 4 717-0407 Control Valve 400 47 732-0324 Compression Spring 5 726-0132 Hose Clamp 5/8" 48 736-0206 Special Washer .378 x 1.00" 6 727-0297 High Pressure Hose Ass'y. x .125 Thd.* .38" I.D. N 49 747-0484 Engagement Rod 3/8' Dia. x 7 727-0299 Return Hose - Valve to Tank 9.0" Lg. N 3/4" I.D. 50 749-0622 Engagement Handle N 8 736-0119 L.-Wash. 5/16" I.D.* 51 710-0106 Hex Bolt 1/4-20 x 1.75" 9 736-0169 L.-Wash. 3/8" I.D.* Lg.* 10 737-0153 Return Elbow 52 710-0152 Hex Bolt 3/8-24 x 1.00" 11 737-0171 90° Solid Male Adapter Lg.* 12 737-0192 90° Solid Male Adapter N 53 710-0180 Hex Bolt 3/8-24 x .75" Lg.* 13 781-0035 Valve Mtg. Plate N 54 710-0299 Hex Bolt 1/4-28 x 1.00" 14 13295 Coupling Support Brkt. Lg.* Ass'y. 55 710-0539 Hex Bolt 3/8-24 x 1.75" Lg. 15 14806 Coupling Shield . (Grade 5) 16 710-0117 Hex Bolt 5/16-24 x 1.00" .56 712-0107 Hex Patch L.-Nut 1/4-20 Lg.* Lg.* 17 710-0157 Hex Bolt 5/16-24 x .75" 57 712-0117 Hex Cent. L.-Nut 1/4-28 Lg.* Thd. 18 710-0653 Hex Wash. Hd. Tap Scr. 58 712-0138 Hex Nut 1/4-28 Thd. 1/4-20 x .38" Lg. 59 712-0158 Hex Cent L.-Nut 5/16-18 19 712-0123 Hex Nut 5/16-24 Thd.* Thd. 20 714-0172 Sq. Key 1/4" x 1/4" x 2.25 ! 60 712-0241 Hex Nut 3/8-24 Thd.* Lg. 61 712-0267 Hex Nut 5/16-19 Thd.* 21 717-0460 Pump wit...
Эта инструкция также подходит к моделям:Прочие инструменты - 245-645-000 (1.76 mb)
Прочие инструменты - 245-642-000 (1.76 mb)