Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection 311082B Pressure Relief Procedure 311082B 3 Pressure Relief Procedure 1. Turn power switch OFF and unplug sprayer power cord. 2. Turn spray/prime valve to PRIME to relieve pressure. 3. Hold metal part of gun firmly to side of a grounded metal pail. Trigger gun. 4. Engage trigger lock. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Clear hose or tip obstruction. Trigger Lock Always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Operation 1. Follow pump priming instructions provided in your sprayer operation manual using the lowest pressure setting at which the pump primes. 2. Turn prime/spray valve to SPRAY position. 3. Disengage gun safety latch. Trigger gun and begin rolling surface until paint comes to roller. 4. If triggering gun cannot supply enough paint for your rolling speed, increase pump pressure. 5. Flush pump, gun and pressure roller immediately after each use to prevent paint from drying in the pressure roller and damaging it. See Cleaning, page 4. Follow this Pressure Relief Procedure when you stop spraying and before cleaning, checking, servicing, or transporting equipment. .............. .......... ................ ti4218a Trigger gun briefly only when you need more paint. Determine how often you must trigger the gun to maintain an even supply of paint to the roller. When you stop painting, relieve pressure, page 3. Elevate roller end of extension tube to prevent paint from draining out. ti4218a .............. Cleaning This is the procedure for flushing/cleaning the pressure roller. The sprayer and gun you are using may have additional flushing/cleaning instructions; such as cleaning filters and screens. See sprayer and gun operation manuals. • Leave pressure roller attached to gun for this procedure. • Refer to roller parts drawing, page 5. 1. Relieve pressure, page 3. 2. Remove roller cover (13) and diffuser (23) from roller frame (1) as follows: a. Using your thumb, press down on clip (5) to release end caps (2 & 4), diffuser, (23) and roller cover (19) into pail. b. Remove roller cover (19) from diffuser (23). c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (19) with water or a compatible fluid for oil-based materials. Cleaning 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside paint pail. 5. Prime pump with water or flushing fluid for oil-based materials. Use the lowest pump pressure setting. 6. Turn prime/spray valve to SPRAY. Perform Step 7 at the lowest pressure possible. 7. Trigger gun until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of roller frame (1) is clear. 9. Shut off pump. Turn prime/spray valve to PRIME. Storage If you are going to store the airless equipment for an extended period of time after flushing with water-based fluid, flush again with Pump Defender™ or mineral spirits/ paint thinner. Leave the fluid in the system during storage. 311082B Parts Parts Ref. 23 No. Part No. Description 1 15B052 FRAME, roller 2 245999 CAP, end (includes seal and retainer) 4 246277 CAP, end (includes seal, retainer, and o-ring) 5 197106 CLIP, roller 6 197118 FITTING, swivel 7 162863 GASKET 8 114049 O-RING 9 197117 NUT, retaining 12 704-25G FITTING, extension, male 13 15A619 GASKET 14 7422R EXTENSION, 20-inch,...
Эта инструкция также подходит к моделям:Прочие инструменты - 287713 (723.36 kb)
Прочие инструменты - 311082 (723.36 kb)