Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Fully tighten the bolts and the hardware from Step 2. G0671/G0672/G0673 Dust Collector -21- 4. Attach the four casters to the legs by threading them into the bottom of the legs, as shown in Figure 15. Figure 15. Attaching casters. 5. With assistance, turn the entire assembly over so that the casters rest on the floor. 6. Use eight 5/16"-18 x 1" hex bolts, (16) 5/16" flat washers, and eight 5/16"-18 hex nuts to attach each collector to the impeller housing with a rubber gasket between the components, as shown in Figure 16. Note: The Model G0673 is a three-phase machine. If it is wired out of phase, the machine may not function properly. Proceed to Test Run on Page 25 to determine if your machine is wired in phase, then proceed to Step 7. The Models G0671 and G0672 are single phase and cannot be wired out of phase. For these models, continue below. 7. Attach the inlet to the top of the impeller housing with the #10-24 x 3/8" Phillips head screw, as shown in Figure 17. Figure 17. inlet mounted on impeller housing. Figure 16. Collector mounted to impeller housing. -22- G0671/G0672/G0673 Dust Collector 8. Secure the hanger into the hanger support with one (Model G0673) or two (Model G0671/G0672) 1/4"-20 x 1/211 hex bolts (see Figure 18). Figure 18. Hanger attached to hanger support (G061/G0672 shown). 9. Mount the hanger assembly on the protruding rod on the collector with one (Model G0671/ G0672) or two (Model G0673) V4"-20 x 1/211 hex bolts, as shown in Figure 19. Figure 19. Hanger assembly mounted onto collector (G0671/G0672). 10. Align the hanger assembly so that the hook is directly over the center of the collector. 11. Repeat Steps 8-10 for the remaining hanger assemblies. 12. Place the loop at the top of each upper collection bag over each hook on the hanger assemblies (see Figure 20). Figure 20. Upper filter bag mounted on hanger assembly. 13. Thread the bag clamp into and around the bottom seam of the upper collection bag (see Figure 21). Bag Clamp Figure 21. Upper filter bag secured to collector. G0671/G0672/G0673 Dust Collector -23- 14. Slip the bottom of the bag with the clamp over the top lip of the collector. 15. Fasten the locking mechanism of the bag clamp to secure the bag to the collector (see Figure 21). 16. Repeat Steps 12-15 for the remaining upper bags. 17. install the lower bags. —Model G0671: Repeat Steps 13-15 in a similar manner to install the remaining lower collection bags on the lower rims of each collector. Then, proceed to Test Run on Page 25. —Model G0672-73: slip the lower plastic collection bag over the bottom lip of the collector and position the bag evenly around the collector. Snag the bag on the hooks to hold it in place until the bag clamp can be secured (see Figure 22). 18. Wrap the bag clamp around the collector, position it between the bottom lip of the collector and the hooks, and fasten the bag clamp to secure the bag to the collector (see Figure 23). Figure 23. Lower collection bag secured to collector. 19. Repeat Steps 17 & 18 for the remaining Model G0672-73 lower bag assemblies. Figure 22. Bottom collection bag snagged on collector hooks. -24- G0671/G0672/G0673 Dust Collector Test Run 5. Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises. Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) (Model G0673 only), the motor turns the correct direction (machine is not wired out of phase). if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 38. if you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance. Awarning Before starting the dust collector, make sure you have performed the preceding assembly instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in serious personal injury or even death! —Strange or unusual noises should be investigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems. 6. Turn the machine OFF by pushing in the RED button on the power switch. 7. Model G0673 Only: Verify that the power is not connected out of phase by starting/ stopping the machine and determining if the motor turns in the correct direction, using the criteria below: —if the impeller turns counterclockwise (as looking down on the inlet port on the impeller housing), it is turning in the correct direction. —if the impeller turns counterclockwise, it is turning in the wrong direction. Stop the machine, shut off the po...
Эта инструкция также подходит к моделям:Прочие инструменты - G0671 (6.56 mb)
Прочие инструменты - G0672 (6.56 mb)