Войти:
Оценок - 2, средний балл: 3.5 ( )

Инструкция по эксплуатации Grizzly, модель CYCLONE G0638

Производитель: Grizzly
Размер: 3.86 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Intake barrel and large cyclone funnel. Model G0637/G0638 (Mfg. Since 04/12) -23- 13. Install the four cyclone mounting brackets with (8) 3/s"-16 x IW hex bolts, (16) 3/s" flat washers, and (8) %"-16 lock nuts (see Figures 22 & 24). Figure 24. Cyclone mounting bracket mounted to collector assembly. 14. Apply the 3 x 6 x 2500mm gasket to the top mating surface of the intake barrel assembly. 15. Keeping the intake barrel assembly on the floor, lower the blower housing assembly over and approximately one inch away from the intake barrel assembly. 16. Using two punches or Phillips screwdrivers as alignment guides (see Figure 25), lower the blower housing assembly onto the intake barrel assembly. 17. Note: Orient the two assemblies so that the large, round intake port of the intake barrel is NOT directly underneath the rectangular outlet port of the blower housing. The outlet port will connect to the canister filters and will not allow room for attachment of the intake ducting to the intake port. Attach the two assemblies with the (12) 5/ieM-18 x 3/4M hex bolts and (12) 5/ieM flat washers (see Figure 26). Figure 26. Securing intake barrel assembly to blower housing assembly. Tip: When installing the two bolts above the intake port of the intake barrel, use duct tape on the bottom of your wrench. This will hold the bolts in the wrench while inserting them in place (see Figure 27). Figure 25. Aligning the mounting holes. Figure 27. Using tape on a wrench in a tight spot. -24- Model G0637/G0638 (Mfg. Since 04/12) 18. Apply the 3 x 6 x 300mm foam tape to the mating surface of the cyclone vacuum port, then attach it to the cyclone funnel with (4) 5/i6M-18 x 3/4M hex bolts and (4) 5/ieM flat washers (see Figure 28). attachment. 19. Lower the blower/intake assembly into the upper stand assembly so that the cyclone mounting brackets align with the mounting holes of the upper stand braces (see Figure 29). Figure 29. Mounting blower/intake assembly to upper stand. 20. Secure the mounting brackets to the upper stand with (8) %"-16 x 3/4" hex bolts, (16) 3/s" flat washers, and (8) 3/s"-16 lock nuts. 21. With assistance and the power lifting equipment, raise the entire assembly high enough to install the lower stand legs. 22. Slide the four lower stand legs onto the bottoms of the upper stand legs—do NOT install the fasteners yet. 23. Slowly lower the weight of the assembly onto the lower stand legs. Note: To keep the assembly stable while completing the next steps, keep the power lifting equipment engaged but not lifting. 24. To allow the mounting holes of the lower stand legs to align properly, slightly loosen the 16 fasteners that connect the lower stand braces to the upper stand legs (see Figure 30). Figure 30. Lower stand legs attached to the upper stand assembly. 25. Secure the lower stand legs to the upper stand assembly with (24) 3/s"-16 x 3/4M hex bolts, (48) 3/s" flat washers, and (24) 3/s"-16 lock nuts. 26. Re-tighten the 16 fasteners connecting the lower stand braces to the assembly. 27. Remove the power lifting equipment from the assembly. Note: The only other use for the power lifting equipment is moving the dust collection system into its permanent position when the assembly is complete. Model G0637/G0638 (Mfg. Since 04/12) -25- 28. Apply the 3 x 6 x 1100mm gasket to the square side of the outlet port. 29. Attach (1) 3 x 15 x 700mm gasket to the outer circular rims of each outlet port. 30. Mount the outlet port to the blower housing with (4) 5/i6M-18 x 1" hex bolts, (8) 5/ieM flat washers, and (4) 5/ieM-18 hex nuts (see Figure 31). Outlet Ports w/Gaskets Figure 31. Filter L-braces mounted to blower housing. 31. Attach the filter L-braces to either side of the outlet port on the blower housing with (6) 5/ieM-18x1" hex bolts, (12) 5/ieM flat washers, and (6) 5/i6M-18 hex nuts. 32. Secure the short filter brace support to the back of the filter L-braces with (2) 3/s"-16 x 3/4M hex bolts, (4) 3/s" flat washers, and (2) 3/s"-16 hex nuts (see Figure 32). 33. Attach the two long brace supports to the filter braces with (4) %"-16 x 3/4" hex bolts, (8) 3/s" flat washers, and (4) %"-16 hex nuts, as shown in Figure 33. L 34. Figure 33. Long brace supports attached. With assistance, position the rubber mounting gaskets between the filter canisters and the long brace supports, and secure the canisters with (8) 5/i6M-18 x 3/4M hex bolts and (8) 5/i6M fender washers (see Figure 34). Figure 34. Canister filters mounted to the long support braces. Figure 32. Short filter brace support attached. 26- Model G0637/G0638 (Mfg. Since 04/12) 35. Attach the 3 x 15 x 700mm gaskets to the upper rim of the canister filter assembly and both rims of the noise muffler. 36. Assemble the 8" x 311/2M flexible ducts, the noise mufflers, and the 8" x 43/4" flexible ducts with the 8" duct clamps (see Figure 35). Figure 35. Ducting and noise muffler connected between blower housing and filter canist...

Эта инструкция также подходит к моделям:
Прочие инструменты - CYCLONE G0637 (3.86 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории