Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Design Dynamics, модель HCM-24-RFP

Производитель: Design Dynamics
Размер: 2.13 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


C. Use only your hand to push in or turn gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified technician. Force or attempted repair may result in a fire. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. LIGHTING INSTRUCTIONS NOTICE: During initial operation the appliance will emit a slight odor for an hour or two. This is due to the "burn-in" of the internal paints and lubricants used in manufacturing. For the first few hours, operatetheappliance with doors and windows open to encourage dissipation of odor. 1. STOP! Read the safety information, column 1. 2. Make sure equipment shutoff valve is fully open. 3. Set switch in the Local position. 4. Wait five (5) minutes to clear out any gas. If you then smell gas STOP! Follow the safety information above. If you don't smell gas, go on to the next step. 5. Turn PilotStat knob to PILOT. Push in on PilotStat knob and press Piezo button until the pilot is lit. 6. Continue to hold PilotStat knob in until LED blinks (one brief blink every two seconds) then release knob. Note: You will need to hold the knob in for about one minute. 7. Turn PilotStat knob to ON See Figure 12, page 9. WARNING: Moving the Local/ Remote switch can cause the main burner to come on immediately. Stand away from the main burner when moving the local/remote switch to avoid possible injury. USING TRANSMITTER/ REMOTE 1. Move switch to REMOTE position (see 2. Press FAN key within 30 seconds. 3. Make sure LED turns on for one second. Figure 12, page 9). or FLAME 115481-01B OPERATING HEATER Continued 4. Press MODE button until mode shows in display window of transmitter/ remote. Press up or down key to change set temperature. 5. To set delay timer, press TIMER button followed by either the up or down key. button until mode is ON. Press button and press the up or MODE the FLAME down arrow key. 6. To change the flame height, press the 7. To change between Fahrenheit and Celsius, press the up and down arrow keys atthe same time and hold for at least three seconds. TO TURN OFF GAS TO APPLIANCE Shut Off Main Burner Using Remote Press MODE button until mode is OFF. Pilot stays lit. Shut Off Main Burner Without Remote Turn PilotStat knob to PILOT. Pilot stays lit. Shut Off Main Burner and Pilot Turn PilotStat knob to OFF. CAUTION: During normal shutdown of this unit, a flash may be observed due to the nature of the burner components. Remain clear of the unit during the shutdown process. INSPECTING BURNERS Check pilot flame pattern and burner flame pat terns often. Flames from the pilot should always be present when the appliance is in operation (see Figure 13). The flame should look similar to those in Figure 14. The flames should look random in appearance with the ember bed glowing red-orange in color. Figure 13 - Correct Pilot Flame Pattern Hardwood Original Log Set California Maple Log Set Kentucky Elm Log Set Figure 14 - Log Sets with Flame Pattern...

Эта инструкция также подходит к моделям:
Прочие инструменты - HCA-18-RFN (2.13 mb)
Прочие инструменты - HCA-18-RFP (2.13 mb)
Прочие инструменты - HCA-24-RFN (2.13 mb)
Прочие инструменты - HCA-24-RFP (2.13 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории