Оценок - 5, средний балл: 3.4
(
)
)
|
Фрагмент инструкции
• Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, push the switch lever on the left side of the tool. To stop the tool, push the switch lever on the right side of the tool. Speed change For HM1202C only The blows per minute can be adjusted just by turning the adjusting dial. This can be done even while the tool is running. The dial is marked 1 (lowest speed) to 6 (full speed). Refer to the table below for the relationship between the number settings on the adjusting dial and the blows per minute. Number Blows on adjusting dial per minute 6 1,900 5 1,800 4 1,600 3 1,300 2 1,050 1 950 CAUTION: • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work. Indicator lamp Indicator lamp 9 For HM1202C only The green power-ON indicator lamp lights up when the tool is switched ON. If the indicator lamp is lit but the tool does not start, the carbon brushes may be worn out, or the electric circuit or the motor may be defective. If the indicator lamp does not light up and the tool does not start, the ON/OFF switch or the mains cord may be defective. The red service indicator lamp lights up when the carbon brushes are nearly worn out to indicate that the tool needs servicing. After approx. 8 hours of use, the motor will automatically be shut off. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 002903 Side handle (auxiliary handle) The side handle can be swung 360° on the vertical and secured at any desired position. It also secures at eight different positions back and forth on the horizontal. Just loosen the clamp nut to swing the side handle to a desired position. Then tighten the clamp nut securely. 1 2 1. Power-ON indicator lamp(green) 2. Service indicator lamp(red) 1 2 1. Side handle 2. Clamp nut 1 2 1. Side handle base 2. Clamp nut 002904 The side handle also can be mounted in the rear groove. Loosen the clamp nut and widen the side handle base. Slide the side handle back to the rear groove and secure it with the clamp nut. 002916 002916 Clean the bit shank and apply bit grease before installing the bit. 1 2 1. Bit grease 2. Bit shank 1. Bit 2. Tool holder cover 1 2 002923 002922 Insert the bit into the tool. Turn the bit and push it in until it engages. If the bit cannot be pushed in, remove the bit. Pull the tool holder cover down a couple of times. Then insert the bit again. Turn the bit and push it in until it engages. After installing, always make sure that the bit is securely held in place by trying to pull it out. To remove the bit, pull the tool holder cover down all the way and pull the bit out. 1 1. Change ring 002939 Bit angle The bit can be secured at 12 different angles. To change the bit angle, slide the change ring forward, then turn the change ring to change the bit angle. At the desired angle, slide the change ring back to the original position. The bit will be secured in place. NOTE: • The change ring cannot turn when the bit is not installed on the tool. OPERATION 002945 MAINTENANCE 001146 1 2 3 1. Commutator 2. Insulating tip 3. Carbon brush 002953 1 2 3 1. Screwdriver 2. Rear cover 3. Screws Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Remove the screws which secure the rear cover. Pry up the rear cover with a screwdriver and remove it. 002954 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 1 2 1. Screwdriver 2. Brush holder cap 1 1. Screws 002967 Lubrication This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubricated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances require that you should lubricate it by yourself, proceed as follows. Run the tool for several minutes to warm it up. Switch off and unplug the tool. 002968 Loosen the six screws and remove the handle. Remove the crank cap using a socket wrench. Rest the tool on the table with the bit...
Эта инструкция также подходит к моделям:Прочие инструменты - HM1202 (131.15 kb)