Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
45-02164 45-02163 H.D. LAWN ROLLER (24" Dia. x 48" Wide) SAFETY PRECAUTIONS 1. Never attach a garden hose to the fill/drain hole when filling. Dangerous pressure build up could occur inside roller. 2. Do not fill roller to maximum weight without checking capability of vehicle to safely pull and stop. 3. Never use roller up and down hills; always work across hills and slopes. 4. Use caution when turning, slowing or stopping. SPECIFICATIONS: Roller Drum: 24" Dia. x 48" Wide Welded Steel O.A. Width: Approximately 52" Bearings: 1" I.D., Replaceable Tow Hitch: Std. Pin Type - 1/2" Hole Weight w/ Water: Up to 910 Lbs. Filled with Water (Note: May be filled with sand) Approx. Sh. Wt.: Approximately 165 Lbs. 5. Always drain roller to keep from freezing. Printed in USA © 2004 Agri-Fab, Inc. Form No. 40255 (9/06) ASSEMBLY INSTRUCTIONS (SEE ILLUSTRATION BELOW) 1. Assemble bearings (Ref. 5) into hitch tubes (Ref. 3) so that bearing flange is against outside of hitch tube. (You may need to place a block of wood against bearing and carefully tap with a hammer.) 2. Place hitch tubes (Ref. 3) onto both ends of roller shaft. Assemble a flat washer (Ref. 6) onto each end of roller shaft and secure with two cotter pins (Ref. 12). 3. Assemble scraper bar (Ref. 2) to hitch tubes (Ref. 3) using two hex bolts (Ref. 9) and hex lock nuts (Ref. 10). Do not tighten yet. 4. Assemble ends of hitch tubes (Ref. 3) together using two hex bolts (Ref. 7) and hex lock nuts (Ref. 10). Do not tighten yet. ADJUST SIZE 5 ?/12 Ref. No. Part No. Qty. Description Ref. No. Part No. Qty. Description 1 1 Roller Drum (Not sold separately) 8 43224 2 Hex Bolt, 5/16-18 x 2-1/4" 2 24868 1 Scraper Bar 9 43084 2 Hex Bolt, 5/16-18 x 1-3/4" 3 48376 2 Hitch Tube 10 47810 6 Hex Lock Nut, 5/16-18 4 24192 2 Hitch Bracket 11 49467 2 Plug, Lawn Roller 5 43632 2 Bearing, Plastic 12 43501 2 Cotter Pin, 5/32" x 1-1/2" 6 43528 2 Flat Washer, 1" 13 47623 1 Hitch Pin 7 46782 2 Hex Bolt, 5/16-18 x 3" 14 43343 1 Hair Cotter Pin 1/8" REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 5. Assemble hitch brackets (Ref. 4) to hitch tubes (Ref. 3) using two hex bolts (Ref. 8) and hex lock nuts (Ref. 10). Do not tighten yet. 6. Tighten bolts and nuts starting with scraper bar (Ref. 2), then ends of hitch tubes (Ref. 3), and finally hitch brackets (Ref. 4). 7. Install hitch pin (Ref. 13) through hitch brackets (Ref. 4) and secure with hair cotter pin (Ref. 14). 8. Adjust plug (Ref. 11) size by twisting handle. Lock a plug in each end of roller drum by flipping handle down. the fastest way to purchase parts www.speedepart.com...