Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации DeWalt, модель D25103

Производитель: DeWalt
Размер: 207.73 kb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THE DRILL. 6. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole. 7. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming. 8. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out. REMOVABLE SDS CHUCK & 3 JAW KEYLESS CHUCK (D25304 ONLY) The D25304 is equipped with a removable quick change SDS chuck as well as a removable 3 jaw keyless chuck. The hammer mechanism 5 English English does not function when the 3 jaw keyless FIGURE 4 F DRILLING IN MASONRY chuck is used. When drilling in masonry, use SDS carbide tipped bits rated for Both the SDS and 3 jaw keyless chuck can cussion drilling and be certain that the bit be easily removed by turning the collar ( E) firm force on the tool to drill most effectively. A smooth, even flow of into the unlocked position (F) to release the dust indicates the proper drilling rate. chuck (Fig. 4). Depth Rod The SDS and 3 jaw keyless chuck can be D G Eeasily attached by inserting the chuck into TO ADJUST THE DEPTH ROD the spindle of the tool and turning the collar 1. Push in and hold the button on the side handle. to the locked position (G). The chuck will 2. Move the rod so the distance between the end of the rod and click when properly installed. end of the bit equals the desired drilling depth. 3. Release the button to lock rod into position. DRILLING IN METAL (D25103, D25203, D25303, D25304) When drilling with the depth rod, stop when end of rod reaches surface of material. An SDS to round shank adaptor chuck is required. Ensure that tool is in drill-only mode. (D25101, D25201 has no drill-only mode). Start Maintenance drilling with slow speed and increase to full power while applying firm CLEANING & LUBRICATION pressure on the tool. A smooth even flow of metal chips indicates the Use only mild soap and damp cloth to clean the tool. Never let any liq proper drilling rate. Use a cutting lubricant when drilling metals. The uid get inside the tool; never immerse any part of the tool into a liquid. exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil; Self-lubricating bearings are used in the tool and periodic relubrication bacon-grease will also serve the purpose. is not required. In the unlikely event that service is ever needed, take your tool to an authorized service location. NOTE: Large (5/16" to 1/2") holes in steel can be made easier if a pilot hole (5/32" to 3/16") is drilled first. Accessories CAUTION: When handling accessories after use, wear work (D25103, D25203, D25303, D25304) gloves. Accessories may be hot and m...

Эта инструкция также подходит к моделям:
Прочие инструменты - D25101 (207.73 kb)
Прочие инструменты - 581054-00 (207.73 kb)
Прочие инструменты - D25304 (207.73 kb)
Прочие инструменты - D25303 (207.73 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории