Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
IMPORTANT: Never hit the engine shaft in any manner, as a blow will cause permanent damage to the engine. 1. Remove the three nuts that secure the pump to the coupling shield. Two nuts are at the bottom corners and one is in the top center. See Figure 5-2. 2. Remove the pump. 3. Rotate the engine by slowly pulling the starter handle until the engine coupling half set screw is visible. Loosen the set screw using allen wrench and slide the coupling half off the engine shaft. 4. Loosen the set screw on the pump coupling half and remove the coupling half. 5. Slide the new engine coupling half onto the engine shaft until the end of the shaft is flush with the inner portion of the coupling half. (There must be space between the end of the engine support bracket and coupling half). Tighten the set screw. 6. Install the pump coupling half and key on the pump shaft. Rotate the coupling half until the set screw faces the opening in the shield. Do not tighten the set screw. 7. Install the nylon “spider” onto the engine coupling half. 8. Align the pump coupling half with the nylon “spider” by rotating the engine using the starter handle. Slide the coupling half into place while guiding three mounting bolts through holes in pump support bracket. 9. Secure with the nuts removed earlier. 10.Set .010” to .060” clearance/gap between the nylon “spider” and the engine coupling half by sliding a feeler gauge or matchbook cover between the nylon “spider” and the engine coupling half and moving pump coupling half as needed. Secure pump coupling half with set screw. See Figure 5-2. NOTE: Make certain the proper clearance/gap is obtained before Figure 5-2 .0600 .0100 Side View-Coupler Set Screw tightening the set screw. TIRES The maximum pressure for the tires is 30 psi. Do not exceed the manufacturer’s recommended psi under any circumstances. Maintain equal pressure on all tires. WARNING Excessive pressure when seating beads may cause the tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of the tire for the recommended pressure. 15 MAINTENANCE MAINTENANCE maintenance Schedule TASKS Before Each Use First 5 Hours Every 25 Hours Every 50 Hours Every 100 Hours SERVICE DATES Lubricate Beam & Wedge • Change Hydraulic Fluid • Change Hydraulic Filter • Clean Reservoir Screen • Check Reservoir Fluid • Check Engine Oil • Change Engine Oil • • Service Air Cleaner • Service Spark Plug • Clean Engine • Figure 5-1 WARNING 2. The warranty on this log splitter does not cover items that have been subjected to operator abuse or negligence. To receive full Do not at any time make any adjustments without first stopping the value from the warranty, the operator must maintain the equipment engine, disconnecting the spark plug wire and grounding it against as instructed in this manual. the engine. Always wear safety glasses during operation or while 3. Some adjustments will need to be made periodically to maintain performing any adjustments or repairs. your equipment properly. GENERAL RECommENDATIoNS 4. Follow the maintenance schedule (Figure 5-1). 1. Always observe the safety rules when performing any maintenance. 5. Periodically check all fasteners and make sure they are tight. 16 MAINTENANCMAINTENANCE hyDRAuLIC FLuID AND INLET FILTER • Check the hydraulic fluid level in the log splitter reservoir tank before each use. Maintain the fluid level within the range specified on the dipstick at all times. • Change the hydraulic fluid in the reservoir every 100 hours of operation. Follow the steps below: 1. Disconnect the suction hose from the bottom of the reservoir tank. 2. Carefully unthread the inlet filter and clean it with penetrating oil. See Figure 5-2. 3. Allow the fluid to drain into a suitable container. 4. Reinsert the filter and refill the reservoir with three (3) gallons of oil. Approved fluids include Dexron® III / Mercon® automatic transmission fluid or a 10 Weight AW hydraulic oil. • Maintain the fluid level within the range specified on the dipstick at all times. NOTE: Always dispose of used hydraulic fluid and engine oil at approved recycling centers only. • Contaminants in fluid may damage the hydraulic components. Flushing the reservoir tank and hoses with kerosene whenever service is performed on the tank, hydraulic pump or valve is recommended. Any repair to the hydraulic components should be performed by a Sears Service Center. WARNING Use extreme caUtion when working with kerosene. it is an extremely flammable flUid. hydraulic Filter • Change the hydraulic filter every 50 hours of operation. Use only a 10 micron hydraulic filter. Order part number 723-0405. bEAm AND SpLITTING WEDGE • Before each use, lubricate both sides of the beam (where it comes into contact with the splitting wedge) with engine oil. The wedge plate on the log splitter is designed so the gibs on the side of the wedge plate can be removed and rotated and/or turned over for even wear. • Make certain to readjust the adjustme...