Оценок - 4, средний балл: 3
(
)
)
|
Фрагмент инструкции
This guards against accumulation of fuel fumes which could result in a fire hazard. 17. Never store log splitter outside without a waterproof cover. Rain will cause rust on the inside of the cylinder. TOWING 1. This unit should not be towed on any street, highway or public road. Any licensing needed to comply with the existing federal, local or state vehicle requirements is the sole responsibility of the purchaser. 2. Before towing, be certain the log splitter is correctly and securely attached to the towing vehicle, and the safety chains (if so equipped or where required by state law) are in place. Leave slack in chains for turning allowance. 3. Do not allow anyone to sit or ride on yotx splitter. They can easily fall off and be seriously injured. 4 TOOLS REQUIRED: Raw Hide or Plastic Hammer 1-1/8", 3/4" 9/16", 1/2" and 7/16" Wrench (or one Adjustable Wrench) E$jr of Pliers f N Additional Adjustable Wrench o THER MATERIALS NEEDED: Approximately 2-1/2 gallons of Dexron II automatic transmission fluid (may be obtained at your local service station or auto parts store). Funnel Engine oil and gasoline (refer to separate engine manual). ASSEMBLY INSTRUCTIONS NOTE FIGURE 1 This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE Reference to right or left hand side of the unit is determined from the operating position, facing forward. See illustration at left. CONTENTS OF HARDWARE PACK (See Figure 1): A (2) Spacers 1-1/2" Long B (2) Tapered Roller Bearings C (2) Castle Nuts 3/4-16 Thread D (2) Cotter Pins E (2) Hub Caps F (4) Hex Bolts 3/8-24 x 1" Long G (9) Lock Washers 3/8" I.D. H (10) Hex Nuts 3/8-24 Thread J (1) Hex Bolt 3/8-24 x 1-1/4" Long K (1) Hex Lock Nut 5/16-18 Thread L (1) Shoulder Bolt M (1) Rubber Washer N (1) Hex Lock Nut 3/8-16 Thread 0 (3) Hex Bolts 3/8-24 x 3/4" Long P (2) Shoulder Bolts Q (2) Lock Washers 5/16" I.D. R (2) Hex Nuts 5/16-18 Thread S (1) Automotive Grease T (1) Hex Bolt 1/4-28 x 1" Long u (1) Hex Bolt 3/8-24 x 1-3/4" Long V (1) Hex Nut 1/4-28 Thread W (1) Hex Lock Nut 1/4-28 Thread X (3) Flat Washers Y (1) Spring z (2) Pivot Brackets WASHER (G) FIGURE 2 LOOSE PARTS IN CARTON: 1) Axle Assembly 2) Wheels 2) Tow Hitch Brackets Tow Hitch Assembly Pivot Stand Hitch Chain Engagement Rod Assembly Engagement Handle Remove log splitter and loose parts from carton. Make certain all parts and literature have been removed from the carton before the carton is discarded. INSTALLATION OF WHEELS 1. Place the axle assembly in position inside the the engine frame assembly as shown in figure 2. Secure with hex bolts (F), lock washers (G) and hex nuts (H). 2. Remove the protective plastic covers from the ends of the axles. 5 HUBCAP TAPERED BEARING (TAPER TO INSIDE 3. TAPERED ROLLER BEARING (B) HUB CAP (E) COTTER PIN (D) FIGURE 3 HEX CASTLE NUT (C) SLOT 3-1/2" LONG HEX BOLTS BRACKET