Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Awarning Gasoline and petroleum products have low flash points and could explode if used to clean machinery. DO NOT use gasoline or petroleum products to clean the machinery. ■w Floor Load The Model G0562 weighs 209 lbs and has a base footprint of 32" x 577/8". Most commercial floors are suitable for the machine. Some residential floors may require additional reinforcement to support both the machine and operator. Working Clearances Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for the machine. See Figure 6 for the overall dimensions of the Model G0562. Awarning Unsupervised children and visitors inside your shop could receive serious personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time. v -12- G0562 3 HP Dust Collector Base Motor and Impeller Components and Hardware Needed: Qty Base ..................................................................1 Casters ..............................................................4 Flange Bolts 5/i6"-18 x V2"..................................16 Tools Needed: Wrench or Socket 12mm....................................1 To assemble the dust collector base: 1. Place the base upside down. 2. Secure the casters into the mounting brackets under the base with the flange bolts (Figure 7). Figure 7. Caster installed on mounting bracket. Components and Hardware Needed: Qty Base .................................................................. 1 Motor and Impeller ............................................1 Flange Bolts 5/6"-18 x V2"....................................4 Tools Needed: Wrench or Socket 12mm....................................1 To install the motor and impeller: 1. Flip the base over onto the casters and locate the mounting holes for the motor and impeller. 2. Position the motor and impeller on the base and secure it with the flange bolts (Figure 8). Figure 8. Motor and impeller attached to base. G0562 3 HP Dust Collector -13- Outlet Canister Support Components and Hardware Needed: Qty Metal “Y” Outlet ................................................1 Flange Bolts 5/6"-18 x V2"....................................8 Rubber Gasket .................................................. 1 Tools Needed: Wrench or Socket 12mm.................................... 1 To install the metal “Y” outlet: 1. Place the rubber gasket around the impeller outlet rim as shown in Figure 9. Figure 9. Placing rubber gaskets over outlet. 2. Secure the metal “Y” outlet in place with the flange bolts (Figure 10). Figure 10. Metal “Y” outlet attached to the impeller. Components and Hardware Needed: Qty Base .................................................................. 1 Canister Supports .............................................. 2 Flange Bolts 5/6"-18 x V2"....................................4 Tools Needed: Wrench or Socket 12mm.................................... 1 To install the canister support: 1. Place the canister support over the holes on the base edge (Figure 11). Figure 11. Canister support attached to base. 2. Secure the canister support in place with 2 flange bolts. 3. Repeat steps 1 & 2 for the second brace. -14- G0562 3 HP Dust Collector ^ Collector Ring Components and Hardware Needed: Qty Collector Rings (R & L)......................................2 Flange Bolts 5/6"-18 x V2"..................................20 Rubber Gaskets ................................................ 2 Tools Needed: Wrench or Socket 12mm....................................1 To install the collector: 1. Place one of the rubber gaskets around the rim of the intake on the collector ring. 2. Secure one of the collector rings to the metal “Y” outlet with 8 flange bolts (Figure 12). Figure 12. Collector ring installed. 3. Attach the canister support to the side of the collector ring with the 2 remaining flange bolts. 4. Repeat steps 1-3 for the other collector ring (Figure 13). Figure 13. Collector rings installed. Canister Filter Components and Hardware Needed: Qty Canister Filters .................................................. 2 Canister Filter Cleaning Handles ......................2 Metal Belt Clamps..............................................2 Wide Foam Strips .............................................. 2 Tools Needed: Wrench or Socket 10mm....................................1 To install the canister: 1. Secure the wide foam strip around the outside top rim of the collector ring as ...