Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Strange or unnatural noises should be investigated and corrected before operating the machine further. If you cannot easily locate the source of an unusual noise or vibration, contact our service department for help. General Operating your Model G0583 is simple and straightforward. Move the dust collector to the machine location, connect the duct, connect the ducting ground, and you are ready to begin. ▲CAUTION DO NOT use the dust collector for any other purpose besides collecting dust from connected woodworking machines. A dust collector should NEVER be used as an air cleaner. For safest use, wear a respirator and use an air cleaner in addition to the dust collector. -20- G0583 1 HP Canister Dust Collector SECTION 6: MAINTENANCE v ! [ 1. ll $1 ▲WARNING Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. \£fj ÊÊÈ0 M ▲WARNING Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. ▲WARNING Wear safety glasses during the entire maintenance process. Failure to comply may result in serious personal injury. Schedule Regular periodic maintenance on your Model G0583 Canister Dust Collector will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: 1. Loose mounting bolts. 2. Worn switch. 3. Worn or damaged cords and plugs. 4. Any other condition that could hamper the safe operation of this machine. 5. Do not let collection bags get completely full. G0583 1 HP Canister Dust Collector Lubrication Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. 3- Bag and Canister Cleaning Always wear a respirator or dust mask and safety glasses when emptying the storage bag (Figure 16). The safest opyion is to seal and discard the entire bag and its contents. Small dust particles can escape the bags during emptying, causing them to become airborne and easily inhaled. This microscopic airborne dust is extremely unhealthy to breathe and can cause serious health problems. Grizzly offers replacement plastic collection bags (Part Number H2290) and canister filters for your Model G0583 Canister Dust Collector. Figure 16. Safely disposing of wood dust. -21- To clean the canister filter: 1. Rotate the canister handle 360° in both direction to vibrate the pleated canister element and free trapped dust particles from the filter (Figure 17). The particles will fall into the collection bag. Figure 17. Rotate canister handle 360° back and forth. To empty the collection bag: 1. Make sure you are wearing a respirator and the canister dust collector is unplugged. 2. When the collection bag is full, un-clamp the collection bag and empty it, or tie it off and dispose of it altogether. 3. Reinstall or replace the collection bag. While the Model G0583 excels at collecting the majority of wood dust produced by your machines, it is not an air filter; therefore, we strongly recommend the supplemental aid of a shop air filter such as the Grizzly G5955 or G9956. Air filters are designed to collect the smaller dust particles that a canister style dust collector cannot trap. -22- G0583 1 HP Canister Dust Collector Troubleshooting SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start, or it growls on start up. 1. Power supply fuse or circuit breaker has tripped. 2. Toggle switch is broken inside. 3. Start capacitor is at fault. 4. Motor fan cover is dented, stopping the fan from being able to spin. 5. Motor is at fault. 1. Disconnect power, and inspect circuit for electrical shorts and repair. Replace circuit breaker if it is old or has tripped many times. 2. Disconnect power, and use an ohmmeter to check switch terminals for continuity, and replace switch if required. 3. Replace start capacitor. 4. Replace motor fan cover (and fan, if damaged). 5. Replace motor. Motor runs slower than normal. 1. Poor electrical connection. 2. Low power source voltage. 3. Motor is at fault. 1. Inspect the power supply for loose, corroded, or overheated electrical connections and repair. 2. Have the power source voltage checked; reduce the length of extension cord. 3. Replace the motor. Loud, repetitious noise, or excessive vibration coming from dust collector. 1. Dust collector is not on a flat surface and wobbles. 2. Impeller fan is damaged and unbalanced. 3. The motor mounting is loose. 4. Impeller is loose on the motor shaft. 5. Motor fan cover is dented, causing the motor fan to hit the cover while spinning. 1. Stabilize the dust collector. 2. Unplug dust collector, and inspect the impeller for dents, bends, loose fins. Replace impeller if any damage is found. 3. Make sure all fasteners on the dust collector are tight. 4. Replace the motor and impeller as a set if the motor shaft and the im...