Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
In places where electric wiring may be hidden behind a wall, floor, ceiling, etc. do not hold or contact any metal parts of the poweer tool. In such cases, metal parts could become electrically live and present a serious shock hazard. 22. KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS. Do not remove covers and screws which have been factory-mounted. They perform important respective roles. Keep them in the original positions. 23. SECURELY MOUNT ACCESSORIES AND BLADES TO THE POWER TOOL MAIN BODY. Extra care must be taken when using the power tool on elevated location (such as a roof ladder, scaffold, or the like) to prevent injury to someone underneath in the event the power tool and/or accessory should drop. 24. ALWAYS KEEP THE MOTOR AIR VENT FULLY OPENED. A constantly open motor air vent is necessary to allow air to come in and out for cooling the motor. Do not allow it to become clogged up, even if dust is blown through it. 25. OPERATE THE POWER TOOL AT THE RATED VOLTAGE. Operate the power tool at voltages specified on its nameplate. 26. NEVER TOUCH THE MOVING PARTS. Never touch the moving parts such as blades, bits, cutters and others. 27. STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS DETECTED. Should the power tool be detected as out of order or should other abnormalities be observed during operation, stop using the power tool immediately. 28. NEVER LEAVE THE POWER TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the power tool until it comes to a complete stop. 29. CAREFULLY HANDLE THE POWER TOOL. Should the power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged. 30. DO NOT WIPE PLASTIC PARTS WITH SOLVENT. Solvents such as gasoline, thinner, benzine, carbon tetrachloride, and alcohol damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water. 31. WHEN REPLACING A COMPONENT PART, ADOPT THE SAME TYPE. When replacing a component part with a new one, adopt the same type of new part. Also, never attempt to repair the power tool yourself. Bring it to an authorized service center for repair. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. GROUNDING INSTRUCTIONS This power tool should be grounded while in use to protect the operator from electric shock. The power tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. If your unit is for use on less than 150 volts, it has a plug that looks like that shown in sketch (A) in Figure on the right. An adapter (see sketches (B) and (C)) is available for connecting sketch (A) type plugs to two- prong receptacles. The green-colored rigid ear, lug, or the like, extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. WARNING: The grounding adaptor, sketch (C), is prohibited in Canada by Canadian Electrical Code Part 1. Therefore, the instructions for its use are not applicable in Canada. Cover of Grounded Outlet Box (C) (A) (B) Grounding Blade Outlet Box Cover of Grounded Adapter Grounding Means EXTENSION CORD Use only three-wire extension cords that have three-prong grounding-type plugs and three- pole receptacles that accept the power tool’s plug. Replace or repair damaged extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current the power tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. MINIMUM GAGE FOR CORD SETS Total Length of Cord in Feet (Meter) 0 – 25 26 – 50 51 – 100 101 – 150 (0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7) Ampere Rating AWG More Not More Than Than 0 – 6 18 16 16 14 6 – 10 18 16 14 12 10 – 12 16 16 14 12 12 – 16 14 12 Not Recommended PARTICULAR PRECAUTIONS ON DEMOLITION HAMMER In addition to the precautions mentioned above, following particular precau...