Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
A Earthing terminal Grounding terminal Warning symbol Alerts user to warning messages Ni-Cad RBRC seal Designates Ni-Cad battery recycling program This symbol designates This symbol designates that this tool is listed to that this tool is listed by Canadian Standards by Underwriters Laboratories. Underwriters Laboratories. This symbol designates that This symbol designates this tool is listed by that this tool is listed by Underwriters Laboratories, the Canadian Standards and listed to Canadian Association. Standards by Underwriters Laboratories. This symbol designates that this tool complies to NOM Mexican Standards. -5 Functional Description and Specifications !WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Rotary Hammer FIG. 1 3-JAW TRIGGER CHUCK SWITCH REVERSING SWITCH LEVER DUST SHIELD LOCKING RING LOCKING SLEEVE DEPTH GAUGE HAND GRIP AUXILIARY HANDLE DEPTH GAUGE RELEASE BUTTON SELECTOR DIAL RELEASE BUTTON SELECTOR DIAL Model number 11224VSRC Shank style SDS-plus® Maximum Capacities: Carbide tipped bits 7/8" Thin wall core bits 2-1/2" -6 Operating Instructions INSTALLING SDS-plus® ACCESSORIES Clean the insert shank end of the accessory to remove any debris, then lightly grease with a light oil or lubricant Insert accessory into the tool holder through the dust shield, while twisting and pushing inward until it locks automatically into place. Pull outward on the accessory to be certain it is locked into the tool holder (Fig. 2). NOTE: The high efficiency available from the rotary hammers can only be obtained if sharp and undamaged accessories are used. The "cost" to maintain sharp and undamaged accessories is more than offset by the "time saved" in operating the tool with sharp accessories. REMOVING SDS-plus® ACCESSORIES !WARNING Accessories may be hot after use. Avoid contact with skin and use proper protective gloves or cloth to remove. To remove an accessory, pull and hold locking sleeve backward and pull bit forward. All accessories should be wiped clean after removing (Fig. 3). FIG. 2 FIG. 3DUST SHIELD LOCKING SLEEVE CHANGING THE CHUCK !WARNING Do not carry the tool by the chuck. Tool may unexpectedly fall if the chuck is not fully engaged. The SDS-plus chuck can easily be exchanged for the 3-jaw chuck supplied with you tool. Hammer drilling and chiseling are only possible when using the SDS-plus chuck with SDS-plus shank accessories. The 3-jaw chuck converts your tool for use with a variety of straight shank bits for drilling and driving. REMOVING THE SDS-plus® CHUCK Grasp the locking ring of the SDS-plus chuck and pull forcefully in direction of arrow and remove from tool (Fig. 4). ATTACHING THE 3-JAW CHUCK Grasp the 3-jaw chuck firmly with your hand and push it onto the tool with a twisting motion until you hear it lock into place (Fig. 5). Pull outward on the chuck to be certain it is locked into the tool. FIG. 4 FIG. 5LOCKING RING 3-JAW CHUCK -7 INSTALLING ACCESSORIES 3-JAW CHUCK Hold chuck collar with one hand and rotate chuck sleeve in direction of arrow with the other hand until the jaws are open (Fig. 6). For small bits, open jaws enough to insert the bit up to the flutes. For large bits, insert the bit as far as it will go. Insert bit, hold the chuck collar with one hand and rotate chuck sleeve in direction of arrow with the other hand until it latches. Then clamp the accessory by continuing to turn the chuck sleeve forcefully in direction of arrow until you hear a ratcheting sound (Fig. 7). Note: If after opening the chuck completely you hear a ratcheting sound when closing, simply open it a quarter turn and then resume closing the chuck. The ratcheting sound will stop. REMOVING ACCESSORIES 3-JAW CHUCK To remove a accessory, hold chuck collar with one hand and rotate chuck sleeve in direction of arrow with the other hand until the accessory can be removed (Fig. 6). FIG. 7FIG. 6 CHUCK COLLAR CHUCK SLEEVE CHUCK COLLAR CHUCK SLEEVE VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed trigger switch. The tool can be turned "ON" or "OFF" by squeezing or releasing the trigger. The speed can be adjusted from the minimum to maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed. REVERSING SWITCH LEVER !CAUTION The reversing switch lever is located above the trigger switch and is used to reverse rotation of the bit. The reversing switch should only be activated when the motor is "OFF" and when bit is at a complete standstill. To use tool in "Forward" rotation move lever to left side of tool, to "Reverse" the rotation of the bit move the lever to the right side of the tool. SELECTOR DIAL The selector dial allows the tool to be set for various applications as listed in the chart (Fig. 8). !CAUTION Do not operate the selection dial...