Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
When installing and assembling your surround package, it is recommended that two or more people be involved. Do not use the unit during an electrical storm. Do not climb on top of the surround package. While the surround package is made out of high-quality material and is extremely durable, it is not meant to support weight. In addition, falling off of the surround package while climbing on it can result in serious injury or death. Do not attempt any repair without consulting the manufacturer first. Unauthorized repairs will void the manufacturer’s warranty (within the first 90 days). Assembly . 1 Tools and Materials 1 Step Assembly 1 Planter Assembly 5 Bar Stool Assembly . 6 Bar Assembly and Installation . 7 Bench Assembly 13 Panel Assembly . 15 Maintenance . 17 Warranty Information 18 Copyright 2008-2009 LMS, Inc. All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas™ and Cal Enclosures™ are registered trademarks. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20091033, Rev. A 12/16/08 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/ or assistance, please contact: LMS Customer Service Department 1462 East Ninth Street Pomona, CA 91766. Toll Free: 1-800-CAL-SPAS Fax: 1-909-629-3890 1 Assembly 2009 Spa Surrounds LTR20091033, Rev. A Assembly Whether you assemble your surround package yourself or hire someone to do it, your new surround package needs to be assembled in a specific order. Our Cal Enclosures professionals have determined through their experience that this is the easiest way to assemble your surround package. Tools and Materials Utility knife 25’ tape measure Cordless drill 100’ extension cord Electric drill Phillips-head drill tips 1/8” pilot hole drill bit 9/16” socket Slotted-head drill tips Sandpaper (various grades) Redwood stain Wood putty Gray wash stain Rags 1/2” ratchet and impact drill 1/2” carbide drill bit (masonry bit) Step Assembly Two Tier, 30” Step Stand the legs up at 30” apart. Place the upper step on top of the upper section of the step.1. To attach the step, screw in 4 screws (2 at each rear corner): 1 into the step leg and 1 into the step itself.2. Place the lower step on the lower section of the step.3. To attach the step, screw in 4 screws (2 on each on the outside of the step). Use the toe-in method on both 4. sides, as shown. 2 Assembly 2009 Spa Surrounds LTR20091033, Rev. A Package R Step Assembly Package D, E, and I Step Assembly Cal Select Step Assembly Planter Assembly Bar Stool Assembly Attach the bar stool legs to support the brace using the provided 2 .” screws. There will be a total of 12 1. screws. Place the bar stool seat on a flat surface. (Make sure the finish side is on the ground.) Attach the leg 2. assembly using four 2 .” screws. Bar Assembly and Installation Package B and M Package C, J, and N Package P and G NOTE: The manufacturer recommends mounting corbels on the cabinet so that the bar top sits just under the spa lip. Using 2 1/2” screws, mount the corbels directly to the cabinet wall. Make sure that the corbels are horizontally 1. level with each other. Mount the bar top to the corbels with the 2 1/2” screws. The screws must be mounted from the underside 2. of the bar top. Make sure that the bar top rests just below the lip of the spa. Package R Bench Assembly Package P and G Package R Panel Assembly Package I Package J Maintenance Your surround package was designed with low cleaning and maintenance in mind. We recommend that the surround package be cleaned at least twice a month (or more, if needed). When cleaning your surround package, do not use cleaning solvents -- using a sponge and water will be fine. For ground-in dirt and grime, refer to the following section. Maintaining your surround package is an easy task. We recommend that every six months you inspect your surround package. If your surround package is redwood, take note of any deformities in the wood (i.e. cracking, peeling, dirt, grime, etc.). Wipe the stained area clean and reapply until the sanded area matches the rest of the surround package. If your surround package is Cal Select, wipe off any dirt or grime using a sponge and water. Condition the Cal Select with Cal Spas Vinyl Cleaner and Conditioner. Follow directions on label. Warranty Information See your Cal Enclosures surround package dealer for a copy of the applicable warranty, details and any questions you may have regarding the warranty coverage on your surround package. Warranty Limitations The Limited Warranty is void if the surround package has been subject to negligence, alteration, misuse, abuse, repairs by non-LMS authorized representatives, acts of God and any other cases beyond the control of LMS. Examples of common acts invalidating this warranty include but are not limited to: Use ...