Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
2) Slide the door onto the two hinge pins making sure the two pieces are fl ush together. See diagram 1. Diagram 1 Diagram 3 Diagram 2 Diagram 4 Diagram 2 Diagram 1 Diagram 3 LOG INSTALLATION Note: Do not force logs down. INSTALLATION 3) Place the left front log, carefully sliding it down onto the left pins of the front burner. See diagram 2. 4) Place the right front log, carefully sliding it down onto the right pins of the front burner. See diagram 3. 5) Distribute the embers along the front burner but do not cover the burner ports and around the logs. Place the large embers on the fl oor of the fi rebox. Place the lava on the burner tray in front of the left and right front logs. See diagram 4. WARNING: Dangerous operating conditions may occur if these logs are not positioned in their approved locations. Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot and burner operation. The gas log kit contains the following: a) Front Right Log - Part # 902-245 b) Front Left Log - Part # 902-244 c) Rear log - Part # 902-246 d) Embers - Part # 902-151 (2 bags) e) Lava - Part # 902-154 (1 bag) (Part # 653-930 for the set of three logs) 1) Remove the logs from the box and carefully unwrap them. The logs are fragile, handle with care - DO NOT FORCE into position. 2) Place the rear log, carefully sliding it down onto the pins, with the fl at side of the log facing the back of the unit. See diagram 1. 3) Close the door. The latch plate must be centered around the alignment pin. See diagram 2. If the latch plate interferes with the corner of the stove you may want to angle the plate slightly so the door closes more easily. 4) The latches should already be at the proper setting. If they are too hard or too easy to close, you may want to adjust them by turning the latch. See diagram 3. 5) Remove the blue plastic protective coating. 6) Test the seal around the door by placing a piece of paper between the unit and the door, close the door and try to pull the paper out. If it slips out easily, then the door is not properly sealed. Turn the adjustable catch to tighten or loosen the latch. See diagram 3. Note: The door latch may require adjustment as the door gasket material compresses after a few fi res and after glass replacement. Turn the latch to tighten or loosen the latch. INSTALLATION OPTIONAL REMOTE CONTROL Use the Regency Remote Control Kit approved for this unit. Use of other systems may void your warranty. The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate. 1) Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the fi replace to that location, use Thermostat Wire Table. 2) Connect the wires as per the wiring diagram above. CAUTION Do not connect the millivolt remote control wires to the 120V wires. 3) Install 3 AAA alkaline batteries in transmitter and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation. Thermostat Wire Table FINAL CHECK Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes: 1) Clocking the appliance to ensure the correct firing rate (rate noted on label) at 15 minutes. 2) If required, adjusting the primary air to ensure that the flame does not carbon. First allow the unit to burn for 15 min. to stabilize. CAUTION Any alteration to the product that causes sooting or carboning that results in damage to the exterior facia is not the responsibility of the manufacturer. 3) Ensuring that the appliance is venting correctly. See page 8. Recommended Maximum Lead Length (Two-Wire) When Using Wall Thermostat (CP-2 System) Wire Size Max. Length 14 GA. 50 Ft. 16 GA. 32 Ft. 18 GA. 20 Ft. 20 GA. 12 Ft. 22 GA. 9 Ft. OPTIONAL WALL THERMOSTAT A wall thermostat may be installed if desired. Connect the wires as per the wiring diagrams on page 13. Use table on this page to determine the maximum wire length: Note: Preferable if the thermostat is installed on an interior wall. Regency offers an optional programmable thermostat but any 250-750 millivolt rated non- anticipator type thermostat that is CSA, ULC or UL approved may be used. CAUTION Do not connect the millivolt wall thermostat wires to the 120V wires. Regency U41-3 ULTIMATE Gas Fireplace Insert INSTALLATION This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/ thermostat will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation. WIRING DIAGRAM Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges. CAUTION: Label all wires prior to disconnection wh...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - U41-LP3 (1.6 mb)