Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
IMPORTANT!This door is designed to accommodate walls that are less than 3/8.(1 cm) out of plumb. Verify the area the door will be attached to is within 3/8.(1 cm) or better of plumb. The door may not function properly if the wall is more than 3/8.(1 cm) out of plumb. Before beginning the installation, measure the dimensions of the opening and confirm the model of door you are installing is the correct size. The bath/shower should be installed at this time, including finished wall materials. Safety Glasses Level Caulk Gun File Knife PliersMiter Box Pencil or Felt Tip Marker Tape Measure Masking Tape Silicone Sealant Center Punch Assorted Screwdrivers Miter Saw or Hack Saw with 32 Teeth Per Inch Blade Drill and 5/16" bit Claw Hammer Plus: • Drop Cloth • Tile or Masonry Bit (if installing onto tile walls) CAUTION:Riskofinjuryorproductdamage.Do not attempt to cut tempered glass. IMPORTANT!This door is designed to accommodate walls that are less than 3/8.(1 cm) out of plumb. Verify the area the door will be attached to is within 3/8.(1 cm) or better of plumb. The door may not function properly if the wall is more than 3/8.(1 cm) out of plumb. Before beginning the installation, measure the dimensions of the opening and confirm the model of door you are installing is the correct size. The bath/shower should be installed at this time, including finished wall materials. Safety Glasses Level Caulk Gun File Knife PliersMiter Box Pencil or Felt Tip Marker Tape Measure Masking Tape Silicone Sealant Center Punch Assorted Screwdrivers Miter Saw or Hack Saw with 32 Teeth Per Inch Blade Drill and 5/16" bit Claw Hammer Plus: • Drop Cloth • Tile or Masonry Bit (if installing onto tile walls) 1035946-2-C 2 Sterling Parts Identification Screw Cover Screw # 8-32 x 3/8" Roller Screw Towel Bar Bracket Screw #8 Self-Drilling Screws Shelf Support Shelf Hook Top Track Tape Track Extension Rail Center Jamb Storage Column Assembly Front Bushing Bottom Track Towel Bar Wall Jamb Rear Door Panel Inside Panel Guide Bushing Pile Seal Anchor Bumper Insert Bumper Sterling 3 1035946-2-C Parts Identification Anchor (6) Bushing (2) Screw (7) Bumper Insert (2) (1) Tape Screw (2) Screw Cover (12) Screw (4) Front Bushing (2) Hook (2) Pile Seal (1) Bumper (2) Screw (6) Roller (4) Anchor (6) Bushing (2) Screw (7) Bumper Insert (2) (1) Tape Screw (2) Screw Cover (12) Screw (4) Front Bushing (2) Hook (2) Pile Seal (1) Bumper (2) Screw (6) Roller (4) 1035946-2-C 4 Sterling 1. Determine the Installation Configuration NOTE: Determine the configuration of your installation. The storage shelves may be mounted on either side of the installation. 2. Locate the Bottom Track NOTE: Make sure the gap in the bottom track assembly is positioned on the storage column side of the threshold. If needed, remove the rail and track extension and reinstall them in the opposite end of the track. Place the bottom track on the flattest part of the bath/shower ledge with the leg toward the outside of the shower. Position the bottom track so there is a 3/4. (1.9 cm) equal gap between each wall and the ends of the bottom track. Temporarily secure the bottom track to the ledge with masking tape. Determine Left or Right Shelving Location. Space to be approximately 3/4" (1.9 cm) on each end. Tape to hold placement of bottom track. Storage Column Side Bottom Track Rail Track Extension Bottom Track Leg Toward Outside of Shower Sterling 5 1035946-2-C Press and hold legs together. Finished Wall Level Slots go toward the inside of bath and away from wall. Anchor Slot Inside of Bath 3. Mark the Wall Jamb Locations NOTE: When the wall jambs are properly positioned, the slots will be on the bath side of the wall jamb. The slots should also be positioned away from the wall, closer to the door. Position a wall jamb against a wall directly in line with the bottom track. The wall jamb should sit flat against the wall, with the slots to the inside of the shower and away from the wall. NOTE: The wall jamb must sit flat on the bottom ledge. If your ledge has a curve in the corners at the side wall, it may be necessary to shape the bottom end of the wall jamb with a file. Slide the ends of the bottom track assembly flush against the wall jambs. Make sure the wall jamb is properly situated. Use a level to plumb the wall jamb vertically and mark the hole locations on the wall. Repeat the procedure with the other wall jamb. Remove the bottom track assembly and wall jambs. NOTE: When installing on ceramic tile, use a center punch to nick the surface of the glaze. Tap the center punch lightly with a hammer to avoid cracking the tile. Lightly center punch the hole locations. Drill a 5/16. hole at each mark. Use a tile or masonry bit for ceramic tile. Thoroughly clean the shower floor ledge and wall. Press and hold the legs of each anchor (provided) together and insert the anchor legs into the pre-drilled mounting holes. Repeat for all the anchors. 1035946-2-C 6 Sterling 4. Install the Wall Jambs NOTE: W...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - Bypass Shower Doors 6075 (1.9 mb)