Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Please read and understand these instructions before beginning your installation. Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation. IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM. INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. WH Report No. J9902-5865C-231 TABLE OF CONTENTS TABLE OF CONTENTS 2 Tools and Building Supplies ............ page 2 Precautions ..................................... page 3 Introduction ..................................... page 3 Clearances/Height Requirements ..... page 3 Chimney System ............................. page 3 Assembly Outline ............................. page 4 Location of Fireplace ....................... page 4 Assembly Steps ............................... page 5 Preinstallation Notes........................ page 5 Clearances ....................................... page 5 Installing the Fireplace ..................... page 5 Fireplace Specifications .................. page 6 Framing Specifications.................... page 7 Installing the Chimney System ........ page 8 30° Offset through Floor/Ceiling ...... page 9 Ten Foot Rule Summary .................. page 11 Multiple Terminations ...................... page 11 Chimney Component Calculations ... page 11 Special Offset Instructions............... page 12 Offset Calculations ........................... page 12 Vertical Elevation Chart ................... page 12 Offset Elevation Chart ..................... page 13 Installing Offsets.............................. page 14 Optional Equipment Considerations. page 14 Forced Air Kits ................................. page 14 Combustion Air Kits ........................ page 15 Gas Line Connection ........................ page 15 Vent Free Appliances ....................... page 15 Glass Doors ..................................... page 16 Cold Climate Insulation .................... page 16 Fireplace Finishes ............................ page 16 Mantels and Trim............................. page 16 Hearth Extensions/Wall Shields ....... page 16 Finish Requirements ........................ page 18 Installation Components .................. page 19 IMPORTANT: PLEASE READ AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY. 1. Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety. Failure to follow them could cause a fireplace malfunction resulting in serious injury and/or property damage. 2. Always check your local building codes. The installation must comply with all local, regional, state and national codes and regulations. 3. These fireplaces must be installed with Security Chimneys FTF8 (8" inside diameter) Chimney System only. These systems are intended for use in any application where a traditional masonry type fireplace would apply. The chimney system must always vent to the outside of the building. 4. To ensure a safe fireplace system and to prevent the build-up of soot and creosote, inspect and clean the fireplace and chimney prior to use and periodically during the heating season. 5. Use solid fuel only. DO NOT use artificial wax based logs, chemical chimney cleaners or flame colorants in your fireplace. 6. DO NOT use charcoal or coal under any circumstances. 7. NEVER use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this fireplace. Keep any flammable liquids a safe distance from the fireplace. 8. NEVER leave children unattended when there is a fire burning in the fireplace. 9. Always keep flue damper open when heat is present in the fireplace. 10. Before servicing, allow the fireplace to cool. Always shut off any electricity or gas to the fireplace while working on it. This will prevent any possible electrical shock or burns. 11. This fireplace is not intended to heat an entire home or be used as a primary heat source. It is designed to ensure homeowner comfort by providing supplemental heat to the room. 12. Always ensure an that adequate supply of replacement combustion air from the outside of the house is accessible to the fire to support normal combustion. Fireplaces consume large volumes of air during the normal combustion process. In the event the home is tightly sealed with modern energy efficient features, the optional combustion air kit may not provide all the air required to support combustion. The manufacturer is not responsible for any smoking or related problems that may result from the lack of adequate combustion air. It is the...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - Merit Series RDI-36-H (722.96 kb)