Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY! NOTE: For proper operation product requires a minimum of 25 psi working line pressure 30 (762mm) OR 32 (813mm) 14-3/4 (375mm) 9 (229mm) 29-1/2 (749mm) 7-1/2 (191mm) 191mm (7-1/2) 14-1/2 (368mm) OR 16-1/2 (419mm) C/L OF WASTE OUTLET (4) 7/8 (22mm) DIA. HOLES SUPPLY AS REQUIRED * 5/8 (16mm) 3-1/4 (83mm) 1-1/2 (38mm) 5-1/4 (133mm) 3-7/8 (98mm) FINISHED WALL FIN. FLOOR 3-1/4 (83mm) 3/4 (19mm) REF. 6 (152mm) 8-1/2 (216mm) 4-1/8 (105mm) OR 6-1/8 (156mm) 19-1/2 (495mm) C/L FIXTURE MOUNTING Fixture studs should project 2-1/8" from face of finished wall. Front ViewSide View FINISHED WALL 2-1/8" (4) STUDS Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for the Physically Challenged When installed, top of seat is 17" to 19" (432mm to 483mm) from the finished floor. ! Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2006 730480-100 Rev B 3 Place back-up nuts on both bottom bolts, and the top left-hand bolt only. Adjust the two lower back-up nuts so that front face of nuts is flush with finished wall. Adjust waste horn to project 5/16" from finished wall. FINISHED WALL CLOSET CARRIER SYSTEM (3) NUTS WASTE HORN 5/16 NOTE: Bearing nuts and washers must be set to take full loading from the fixture allowing 1/16" clearance between fixture and wall. Follow support manufacturer's recommended setting of closet outlet connection. Place felt or neoprene gasket (wax ring not recommended) on closet outlet. When the fixture is installed, closet outlet gasket must be compressed sufficiently to assure a gas and watertight seal. The following steps require a helper: Install bowl on support using cap nuts and fiber washers with the back-up nuts and washers. DO NOT APPLY TOP RIGHT FIBER WASHER AND CAP NUT UNTIL OTHER CAP NUTS HAVE BEEN FIRMLY TIGHTENED USING A WRENCH. Install top right cap nut with fiber washer and run up hand tight. Wrench tighten approximately 1/4 turn. Apply sealant to gap between bowl and finished wall. Remove excess sealant. 4 Using a level, adjust the top left back-up nut so that it is in the same vertical plane as the lower left back-up nut. (If wall surface is irregular, the three back-up nuts must be positioned to allow a minimum 1/16" gap between fixture and wall surface.) FINISHED WALL 1/16" (IRREGULAR WALL SURFACE) LEVEL 6 SPONGE WASHERTANK MTG. BOLTS SANITARY BAR NUT WASHER INSTALL TANK AND TOILET SEAT Install large rubber gasket over threaded outlet on bottom of tank with tapered side out and lower tank onto bowl so that the tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against sanitary bar on bowl. ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! Install toilet seat according to manufacturer's directions. 5 730480-100 Rev B -2 7 TANK COUPLING NUT FLEXIBLE SUPPLY WATER INLET WASHER 8 SET SCREW 1/32" APPROX. VALVE NUT COMPRESSION COLLAR TRIM PLATE VALVE Connect water supply line between shutoff valve and tank water inlet fitting. Tighten coupling nuts securely. Turn on supply valve and allow flushometer tank to fill. Check for leakage at fittings, tighten or correct as needed. CONNECT WATER SUPPLY ADJUSTMENTS The flushometer tank is designed and factory-adjusted to provide a consistent, safe seal depth in the bowl after each flush. Field refill adjustment is not required. The refill has been preset and locked. FLUSH ACTUATOR ADJUSTMENT - The spacing between the bellcrank and flush actuator may be adjusted to assure positive operation of the trip lever. Proceed as follows: Remove tank cover and check that there is approximately 1/32" (0.8mm) gap between the top of the actuator and bottom of the spring rod when it is lifted to remove slack from linkage. If necessary, loosen set screw in actuator cap and turn cap to increase gap (clockwise) or decrease gap (counterclockwise), as needed. Tighten setscrew securely after adjustment is completed. Replace tank cover. REPAIR PARTS LIST NOTE: "XXX" and "YYY" represent color or trim finish options. Specify when ordering. ITEM PART NO. DESCRIPTION QTY 1 2 3 4 5 6 7 8 9 10 1 1 1 1 1 1 1 1 1 1 1 1 738473-YYY0A 738494-YYY0A 4098.100.XXX 4098.800.XXX 735083-400.XXX 3402.016.XXX 738493-0070A 738495-0070A 730599-0070A 738496-0070A 047562-0070A 047563-0070A 730292-0070A 735083-600.XXX 603111-0030A TRIP LEVER-LH TRIP LEVER-RH TANK (COMPLETE WITH COUPLING COMPONENTS AND L.H. TANK TRIM) TANK (COMPLETE WITH COUPLING COMPONENTS AND R.H. TANK TRIM) TANK COVER BOWL SPRING ROD ASSEMBL...