Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed! INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall. 2 3 CLOSET FLANGE CLOSET BOLTS 7 3 0 9 4 5 - 1 0 0 R e v . C CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 2 0 0 7 ! NOTE: Pictures may not exactly define contour of china and components. S A V E F O R F U T U R E U S E INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Skyline Champion®4 2-piece Toilets Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench Recommended fitting type for back-to-back installations. Depending upon your plumbing and venting conditions, the flow from the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water downward and away from the other toilet. NOTE: BACK-TO-BACK INSTALLATION MODEL A B C D DIMENSIONS 2067.014 Elongated Right Height™ 2-pc Toilet 2112.014 Round Front Normal Height 2-pc Toilet 18-1/2" 470mm 16-1/2" 419mm 30-3/8" 772mm 34-3/8" 873mm 16-1/2" 419mm 15-1/4" 387mm 28-3/8" 721mm 33-1/8" 841mm 2219.014 Elongated Normal Height 2-pc Toilet 18-1/2" 470mm 15-1/4" 387mm 30-3/8" 772mm 33-1/8" 841mm ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet Normal Height Round Front Two Piece Toilet FINISHE D WALL Normal Height Elongated Two Piece Toilet 19mm ± 6mm (1 ± 1/4) B FINISHED FLOOR 305mm (12) C C/L OF OUTLET 83mm (3-1/4) 235mm (9-1/4) A C/L OF SEAT POST HOLES 140mm (5-1/2 CENTERS) 362mm (14-1/4) 264mm (10-3/8) 16mm (5/8) D 498mm (19-5/8) SUPPLY AS REQ'D 254mm (10) 152mm (6) 254mm (10) 356mm (14) * 2067.014 Right Height™ Elongated: 3225.016 Bowl and 4077.014 Tank 2112.014 Round Front: 3110.016 Bowl and 4077.014 Tank 2219.014 Elongated: 3121.016 Bowl and 4077.014 Tank 7 3 0 9 4 5 - 1 0 0 R e v . C SEALANT WAX RING 4 5 INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base. POSITION TOILET ON FLANGE a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! - 2 - CLOSET BOLT NUT TAPERED WASHER FLANGE MANIFOLD INSIDE WATERWAY - DO NOT REMOVE 6 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. ! CLOSET BOLT WASHER NUT BOLT CAP 9a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings. CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE. CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding. These parts must be used as illustrated to insure water-tight connection. Use of existing coupling nut may result in water leakage. Water supply tube or pipe must extend at least 1/2" inside threaded shank of valve (does not apply to flanged tubing). Use existing coupling nut and washer. Use existing spiral cone washer. Fluidmaster cone washer may not seal completely on spiral type supply line. Captive cone washers already included. No additional washers needed. METAL/COPPER FLARED TUBING METAL FLANGED TUBING METAL SPIRAL TUBIN...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - 2067.014 Right Height (1.72 mb)