Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
by C O L L E C T I O N™ T H E BOSS GROOVE IN FAUCET BASE LAVATORY SINK OR MOUNTING SURFACE 3 2 6 7 1 5 6 4 1 Insert LIFT ROD (7). From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto STUD (4). Pull Faucet to front of sink, so STUD (4) rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet From below, install MOUNTING GASKET with RETAINING WASHER (5) and Nut (6) onto STUD (4). Pull Faucet to front of sink, so STUD (4) rests against sink hole. Before final tightening, align Faucet and ESCUTCHEON (1) so they are centered on mounting surface. Tighten NUT (6) to secure Faucet For single hole installation use ESCUTCHEON RING (2). Install SEAL WASHER (6) into groove in ESCUTCHEON RING (2) base and place over over mounting hole in lavatory sink or mounting surface. Insert LIFT ROD (7). Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON RING (2). Seat ESCUTCHEON RING (2) boss into groove in Faucet base. Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss into groove in Faucet base. INSTALL FAUCET Turn off water at CAUTION main supply. INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON PLATE (1) or for center hole only with ESCUTCHEON RING (2). INSTALLATION with ESCUTCHEON PLATE (1) INSTALLATION with ESCUTCHEON RING (2) BOSS GROOVE IN ESCUTCHEON RING BASE Remove as much surface dirt and film using clear water and soft cotton cloth (as described above). Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. DO NOT: Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers No sealant is required unless mounting surface is uneven for 3-hole (4" centers) installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON PLATE (1) over mounting holes on lavatory sink or mounting surface. M968290A 3 WATER SUPPLY CONNECTIONS Note: FLEXIBLE HOSES (1, 2) on FAUCET (3) are (17-1/2") in length from base of faucet. If longer supply length is required installer must purchase adapters and additional supplies to complete connections. Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking . Connection on FLEXIBLE HOSES (1, 2) are 3/8" compression. Connect LEFT SUPPLY (1) to Hot shut off valve and RIGHT SUPPLY (2) to Cold shut off valve. Use adjustable wrenches to tighten connections. Do not over tighten. 1 3 COLD 2 HOT SHUT OFF VALVE (17-1/2") 3/8" compression 1 2 A 3 4 5 10 11 12 8 G F D E 6 7 F C 9 1-1/4" FIGURE-3A: O-RING 9 2 INSTALL POP-UP DRAIN Push Tail piece (11) down into Trap (C) (threaded end up). Assemble Pivot Rod (9) as shown in Figure-3A. Notice the position of the Concave Washer (G). Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot Nut (F). Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side up) onto Drain Body (10). Apply a bead of Putty (D) to underside of Flange (2). Remove one end of Cl...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - 2071S (375.25 kb)