Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Installation Consideration Rough-in 10303181 must be installed, and the wall finished, prior to installation of this trim kit. For the trim to fit properly, the outside surface of the finished wall must fall between the “minimum” and “maximum” lines on the factory installed plaster shields on the rough-in. If the rough-in is too far inside the wall, install extension kit 96259000 (purchased separately) before attempting to install the handle trim. No drain is included with this trim kit. Please consult the sink manufacturer regarding a suitable drain for the specific sink used. ·Remove the inserts from the hot and cold plaster shields. ·Cut the plaster shields so that they extend 1/16” from the wall. Seal around the shields with a suitable, non-staining, waterproof bathroom sealant. ·Lever handle version only: Remove the hot and cold cartridges using a 17 mm deep socket wrench. Replace them with the 1.4 turn ceramic cartridges included with the trim kit. The hot cartridge is marked with notches on the wrench flats. ·On the spout outlet, measure the distance from the brass rough-in to the end of the plaster shield. Record this measurement (“X”). Add 1 7/8” to this measurement. Measure the spout adapter. Mark a point X + 1 7/8” from the o- ring end of the adapter. Cut the adapter at this point. ·Wrap the threads with several layers of Teflon® thread tape. Screw it into the spout port. ·Measure the distance from the plaster shield to the end of the spout adapter. It should measure 1 3/8”. ·Install the outer sleeves to the hot and cold valves. Measure each outer sleeve to a point 3/8” from the surface of the finished wall. Mark the sleeve at this point. Cut the sleeves. Install the inner sleeve. ·Measure the inner sleeve to a point 1.2” from the surface of the finished wall. Mark and cut the inner sleeve at this point. Place the handle over the inner sleeve. ·The handle should be parallel to the floor. If it is not, remove the handle. Remove the handle insert, turn it slightly and replace. The handle should now be parallel to the floor. ·Remove the handles. ·Attach the spout and spout escutcheon to the wall plate with the screws provided. ·Place the plate and spout assembly over the valve. Install the handle escutcheons and the handles. Turn the handle bases clockwise, so that they thread onto the outer sleeves. ·Secure the spout to the spout adapter by tightening the set screw. User Instructions – Lever handle version ·Turn the handle downwards (clockwise for cold, counter- clockwise for hot) to turn the water on. Turn the handle upwards to turn the water off. ·In the off position, the handles should be parallel to the floor. Replacement parts 1 lever handle 39296XXX 2 cross handle 39295XXX 3 hot escutcheon 96759XXX 4 cold escutcheon 96758XXX 5 spout escutcheon 96760XXX 6 escutcheon 96757XXX 7 aerator 13085000 8 fixing set 96393000 9 hot cartridge 96351000 10 cold cartridge 96350000 11 extension kit 96259000 (optional) Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers •To remove lime scale, use only products made specifically for that purpose. Always follow the manufacturer’s instructions when using. •Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will cause considerable damage to finishes and to plastic components. •Never mix cleaning materials. •Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges. Cleaning Procedures •Clean your faucets and shower products as and when required. Regular cleaning will prevent scale buildup and water spotting. •Follow the label instructions. Do not allow any cleaner to remain on the product for longer than necessary. •When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the product. •After cleaning, rinse thoroughly with clear water to remove any cleaner residue. Important •Soap and shampoo residue can also cause damage to the product. Rinse well with clean water after use. •If the surface is already damaged, harsh cleaning materials will cause further damage. Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. („Hansgrohe“). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in materi...