Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Accessories that may be suitable for one product may become hazardous when used on another product. When servicing a product, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Maintain labels and nameplates on the product. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. Keep the Solar Panel free of dirt, dust and grime. Dust covering the Solar Panel will block out sunlight causing a decrease or stoppage of efficiency in recharging the battery. Make sure the area where you wish to install the Solar Light is free of any underground wires or cables. WARNING: Ni-Cd batteries must be disposed of properly. Do not incinerate. The battery may burst, causing personal injury and/or property damage. Contact your local hazardous waste disposal authority for proper disposal. Unpacking When unpacking, make sure the item is undamaged. If any parts are missing or broken, call Harbor Freight Tools at the number shown on the cover of this manual. Assembly AND OPERATING Instructions WARNING! Make sure the Power Switch of the product is in its “OFF” position before making any adjustments to the product. The Power Switch is located under the Light Head (1). Also remove all plastic films from the solar panels before use. The light comes with four main parts. These are the Light Head (1), the Tube (2) Glass Shade (3) and Stake (4). See Figure 1. Decide where you want to place the Solar Light. Choose a location that receives full, direct sunlight for a minimum of six hours a day. During initial charging, set the Power Switch located under the Light Head (1) to “ON”. The Solar Light will need to charge for at least 8-12 hours before using it for the first time. During the day, the Solar Panel on the Light Head (1) converts sunlight into electricity, recharging the batteries. The amount of light received depends on placement of the Solar Light, geographic location and weather. If the weather is cloudy and the panel did not receive a full charge, the Solar Light may not run for the full 10 hours. It will catch up after six hours of direct sun. To assemble the Solar Light, slide the top of the Glass Shade (3) along the grooves under the Light Head (1) until the two pieces lock into place. Attach the Tube (2) to the bottom of the Glass Shade (3). Then insert the top of the Stake (4) into the bottom of the Tube (2). Push the Stake (4) directly into the ground. Make certain that the path of the Stake (4) is clear of any underground wires or cables. Turn the Power Switch under the Light Head (1) to “ON.” Turn the Power Switch to “OFF” to turn off the light and before replacing the batteries. Stake (4) Light Head (1) Glass Shade (3) Figure 1 Tube (2) Replacing the Batteries You should replace the two rechargeable batteries every 12 months. Turn the Power Switch to “OFF”. Slide the Light Head (1) free of the Glass Shade (3). Lie the Light Head (1) top-down and open the two battery compartments. See Figure 2. Remove and properly recycle the old batteries. Make certain that the new batteries are Ni-Cd (“AA”, 1.2V, 600 mAh) rechargeable. Install the new batteries into the Battery Compartment. Make certain that the batteries are placed according to the correct polarity. See Figure 2. Replace the battery covers and reassemble the Light Head and Glass Shade. inspection, Maintenance and cleaning Clean regularly with a damp towel. Do not use solvent for cleaning. Do not put too much pressure on the Solar Panel or accessories while cleaning. Dry thoroughly. WARNING! Make sure the Power Switch is in its “OFF” position before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the Solar Light. Check for loose screws, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. Do not use damaged equipment. Figure 2...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - ONE STOPS 95682 (549.58 kb)