Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Remove the tail light housing from the car. 3. Remove any body trim from the housing so the screws holding the lens on are exposed. 4. Remove the tail light lens. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside of the housing.The flat side of the mounting disk should betoward the outsideand theside with the slight raised center should go in toward the housing. This willalignthe mountin the originalhousing. 9.Secure the back plate with the supplied #6 lock nuts. 10.Make surethe original lens gasketisin place and replace the tail lightlens. 11.Replace the bodytrimand reinstall the tail light housing into the vehicle. 12.Cut off the existing light socketas itwill not be used.Do not strip the wires.Trim the wiresfromLED assembly to appropriate length once mounted,making sure wires are routed cleanlyand securely. 13.Use the supplied moisture resistant pigtail connectors* to attach the wires from the newLEDassembly to the existing vehicle harness.Insert appropriate wire from vehicle harnessandmating LED assembly wire into a connector and crimp following instructionsbelow. *For the bestconnection,soldering isrecommended.But to simplify installation,the supplied connectors willprovide a fastweather resistant connection. Thecorrect crimp method for the supplied connectors is: 1.) InsertUNSTRIPPEDwiresinto the connector and ensurethey are allthey way in byobserving the clear bottom ofthe connectorto see the wires are touchingthe end. 2.) Use pliers to push the blue cap down flush with the edge ofthe clear body,completing theconnection.The connection will only be correct if pressedfirmlydown with pliers. MAN#650234 GREEN wireGREEN wireBROWN wireBROWN wireBLACK wireBLACK wirefrom LED from LED from LED from LED from LED from LED assemblyassemblyassembly assemblyassembly assembly Turn Signal wireTail Light wireGround wirefrom vehiclefrom vehiclefrom vehicleharnessharnessharness LED wiresVehicle harnessTail lightBrownBrown or BlackDriver’s TurnGreenGreen orPinkPassenger’s TurnGreenYellow or PurpleGroundBlackChassis or body 14.Repeat forthe otherside. 15.Test the tail lights, brake lights,and turn signals. Ifthe turn signals do notflash you will need to upgrade yourflasher. If you are replacingonly the rearturn signals a heavy duty electronicflasherfrom your localparts storeshould be able to be used.If you are replacing bothfrontand rear or do nothave front bulbs you will need a no-loadflasher,Dakota Digital part numberLAT-NLF. SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of itsproduct line.In addition, technicalconsultation isavailable to helpyouwork through any questions orproblemsyou may be having installing one ofour products. Please read through the Troubleshooting Guide. There,you willfind the solution to most problems. Shouldyou everneedto send the unit back for repairs,please callour technicalsupport line,(605) 332-6513,to requesta Return MerchandiseAuthorizationnumber.Package the productin a good quality boxalong withplenty of packing material.Ship the productby UPSor insured Parcel Post.Be sure to includethe RMAnumberon the package, and include a complete description ofthe problem with RMA number, your full name and address (streetaddresspreferred), and a telephone numberwhere you can be reached during the day.Any returns forwarrantywork must include a copyof the dated salesreceipt fromyourplace of purchase.Send no money.We will billyou after repair. Dakota DigitalLimited LifetimeWarranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this productthat should it, under normal use and condition, be proven defective in material orworkmanship for the lifetime ofthe original vehicle itwas installed in, such defect(s)will be repaired orreplaced at Dakota Digital’s option. Thiswarrantydoes notcovernor extend to damage to the vehicle’ssystems, and doesnotcover removal or reinstallation of the product. ThisWarrantydoesnotapplyto any product or partthereofwhich in the opinion of the Companyhasbeen damaged through alteration, improper installation, mishandling, misuse, neglect,oraccident. ThisWarranty is in lieu ofall other expressed warrantiesor liabilities. Any implied warranties, including any implied warranty of merchantability,shall be limited to the duration ofthis written warranty.No person or representative is authorized to assume, forDakota Digital,any liability other thanexpressed herein in connection with the sale ofthis product. 4510 W. 61ST St. N., Sioux Falls, SD 57107Phone:(605) 332-6513 FAX: (605) 339-4106 ©Copy...