Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
3 5 1. Mounting Screws (4) 2. Mounting Washers (4) 3. Mounting Spacers (2) 4. Cutting Assembly Release Button 5. Magnetic Lid Holder 6. Can Guide Pin 7. Geared Wheel 8. Piercing Lever 9. Cord Storage 4 Parts and Features Installation This can opener is designed to be installed under a cabinet or shelf. When selecting a location for installation, consider the following: • An electrical outlet should be within easy reach of the plug so the cord does not drape over a heating or cooking appliance, a sink or basin, or get in the way of your normal work space. HINT: Before drilling any holes, plug unit into desired outlet and hold can opener in proposed location to ensure cord will reach. • Do not install can opener above a cooking or heating unit, such as a stove, or above a sink or basin. 1. Remove the mounting template page from the back of the Use & Care booklet. Align the dashed line on the template with the front edge of the top side of the mounting surface and tape in place. Drill four 3.16” (5 mm) holes as indicated and remove the template from the mounting surface. 2. Select the desired number of spacers to use (see Table A on previous page). Place spacer(s) on top of can opener (if applicable). 3. Insert screw through one of the white plastic washers with the flat side of the washer away from the screw head (see Figure 1). Insert screw through hole drilled in mounting surface and into corresponding hole in can opener. Tighten several turns. Do not tighten all the way at this time. Repeat with remaining three screws. 4. Tighten all four screws. Do not overtighten. Figure 1 Height of Front Overhang (Cabinet or Shelf) Spacers Needed 0 to 1.2 inch (1 cm) 0 1.2 to 11.4 inches (1 to 3 cm) 1 more than 11.4 inches (3 cm) 2 Table A 840123500 ENv03.qxd 2/19/04 4:59 PM Page 4 840123500 ENv03.qxd 2/19/04 4:59 PM Page 6 Using Your Can Opener To open cans: 1. Plug cord into electrical outlet. 2. Raise piercing lever up. 3. Hold can against opener support. 4. Place rim of can firmly under can guide pin and against the geared wheel. 5. Press piercing lever all the way down. 6. The motor will begin turning can and cutting lid. (It is not necessary to hold the piercing lever down or to hold the can during the cutting action. ) 7. The motor will automatically stop when the can is open. 8. Remove can from can opener and check can contents to remove any pieces of label or metal shavings. To open bottles: Support bottle beneath the bottle opener with one hand. Place one hand behind the unit for additional support. Open bottles slowly to avoid spilling contents. 6 Cleaning Your Can Opener 1. Unplug cord from electrical outlet. 2. To remove the cutting head assembly, press release button. 3. Wash cutting head assembly in hot soapy water. Rinse and dry thoroughly. Cutting head assembly may also be placed in top rack of dishwasher. 4. Wipe the can opener body and the Remove area behind the cutting head assembly with a damp cloth. Never immerse the can opener in water. 5. To re-assemble, raise lever slightly then slide the assembly onto the body until the release button clicks into place. 7 Re-assemble 840123500 ENv03.qxd 2/19/04 4:59 PM Page 8 Tips and Hints for Best • The can opener will easily open all standard size cans. • If there is a bump, dent, or heavy seam in the can, open the other end of the can or start beyond the problem area. • The motor of your can opener is permanently lubricated and will require no oiling. • To use the cord storage on the back of the opener, push in or pull out the cord as needed. • If piercing lever does not move freely, remove and clean the cutting head assembly. • To lock the cord, turn cord sideways and slide up into narrow portion of cord storage. Customer Service If you have a question about your can opener, call our toll-free customer service number. Before calling, please note the model, type, and series numbers and fill in that information below. These numbers can be found on the bottom of your can opener. This information will help us answer your question much more quickly. MODEL:_____________ TYPE:_____________ SERIES: ______________ 8 The following warranty applies only purchased in the United States and Canada. LIMITED WARRANTY This product is warranted to be free from defects in material and workmanship for a period of two (2) years for Hamilton Beach Portfolio products, one (1) year for Hamilton Beach products or one hundred eighty (180) days for Proctor-Silex products from the date of original purchase, except as noted below. During this period, we will repair or replace this product, at our option, at no cost. THE FOREGOING WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ANY LIABILITY IS EXPRESSLY LIMITED TO AN AMOUNT EQUAL TO THE PURCHASE PRICE PAID, AND ALL CLAIMS FOR SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. There is no warranty with r...