Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
IMPORTANT: Write down the model and serial numbers Read and save these before installing or using Outdoor Bar instructions. Cart. Both numbers are on the model/serial IMPORTANT: number plate, located on the underside, Installer: Leave Installation right front of the Outdoor Bar Cart. Instructions with the consumer. Comsumer: Keep Installation Model #___________________________ Instructions for future reference. Serial # ___________________________ Part No. 8184968 Rev. A Before you start... Product Dimensions Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: DANGER You can be killed or seriously injured if you don’t immediately follow instructions. WARNING You can be killed or seriously injured if you don’t follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. IMPORTANT: Observe all governing codes and ordinances. Built-in Installation 30" (76.2 cm) 36" (91.4 cm) 25-1/2" (64.8 cm)1/2" (1.3 cm) The portable model must have suitable drain systems in accordance with local codes for the ice bin and sink drains. 12" (30.5 cm) 12" (30.5 cm) 10-1/2" (26.7 cm) 23" (58.4 cm) 30" (76.2 cm) 25-1/2" (64.8 cm) Portable and Built-in models Dimensions Provide suitable drain systems in accordance with local codes for ice bin and sink drains. The drains and filter must be accessible. 29" (73.7 cm) 10-5/8" (27.0 cm) 35-1/2" (90.2 cm) Basic Parts of the Built-in and Portable models Side shelves not shown Tools needed: Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed. • Level • Phillips screwdriver • tape measure or ruler • slip joint pliers • pipe wrench • adjustable wrench Parts needed: • 1-1/2" drain system • 1" drain system • NSF- or UPC-listed water connection lines • plumbers putty • clear silicon outlet hose and sink connectors inlet hose and connectors water filter connection and filter bottle well bottle well holder two piece sliding cover support framesingle faucet ice bin bottle rail bottle capcatch pantowel holder bottle opener1-1/2" drain fitting 1" drain fitting Installation - Built-in model WARNING Excessive Weight Hazard Use two or more people to move and install bar cart. Failure to do so can result in back or other injury. Use a certified plumber to connect and install potable water supply and drain system to outdoor bar cart per local code requirements. 1.Set the Bar Cart on a protective surface such as cardboard or a blanket. 2.Make sure you have the drain connections, in accordance with local codes, under the Bar Cart. 3.Remove the bottle rail, bottle cap catch pan and water filter from the ice bin. 4.Remove the faucet from the sink. sink washer locknut 5.Install the faucet and fasten securely. 6.Install the water filter on the sink/faucet side of the cutout. Position the filter so that the plastic hose attached to the filter easily reaches the faucet connection. plastic hose nut connector inlet connector mounting panel 7.Install water inlet connection in a convenient location under the cutout. Position the water inlet connection so that the plastic hose easily reaches the filter inlet connection. plumbers putty 8.Place a small amount of plumbers putty around both the ice bin and sink drain mounting seats. drain washer locknut 9.Install the 1" (2.5 cm) drain fitting in the ice bin and the 1-1/2" (3.8 cm) drain fitting in the sink. Tighten securely. Remove and discard the excess plumbers putty. 10.Ice bin drain and sink drain fittings to be connected to drain system in accordance with local code requirements. apply clearsilicone plastichose filter 11.Apply a bead of all weather clear silicone on the under side of the back and two sides of the top lip. 12.Carefully position the Bar Cart into the cut out. Immediately remove any excess silicone. 13.Connect the plastic hose from the water filter to the faucet connection and tighten securely. plastic hose inlet connector filter 14.Attach the plastic cold water hose from the water inlet connection to the inlet side of the filter. Use N.S.F. or U.P.C.-listed water connection line for water supply to inlet connector. Potable water supply system to be connected to inlet connector per local code requirements. 15.Unwrap the bottle rail and bottle cap catch pan. Position them over the key-lock studs and slide down to lock in place. 16.Unwrap the sliding cover and place into frame on top of the ice bin. Installation - Portable model WARNING Excessive Weight Hazard Use two or more people to ...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - KFBP102LSS (212.74 kb)