Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Box 309, Menomonee Falls, WI 53052-0309 Phone: 1-800-BRADLEY Fax: (262) 251-5817 http:\\215-1187 Rev N; EN 06-915B © 2007 Bradley Corporation Page 1 of 85 4/6/2007 IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with theinstallation, file this manual with the owner or maintenance department. Separate parts from packaging and make sure all parts are accounted for beforediscarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Make sure that all water supply lines havebeen flushed and then completely turned off before beginning installation. Debris in supply lines can cause valves tomalfunction. Hardware supplied by installer must be appropriate for wall construction. Wall anchors used must have a minimum pull-outrating of 1,000 lbs. The Adaptive® Infrared control must be connected with a 24 VAC Class II transformer. Connections to 110 VAC can cause personal injury and will result in damage to the electronics. Product warranties may be found under “Product Information” on our web site at IMPORTANT ! Lire ce manuel d’installation dans son integralite pour garantir une installation appropriee. Une fois celle-ci terminee, classer ce manuel aupres du service a la clientele ou d’entretien. Separer les pieces de l’emballage et veiller a bien avoir toutes les pieces avant de jeter lemateriau d’emballage. Le cas echeant, ne pas commencer l’installation avant d’avoir obtenu les pieces manquantes. Veiller a bien vidanger et fermer toutes lesconduites d’eau avant de commencer l’installation. Tout debris dans les conduites d’alimentation risque de provoquer unmauvais fonctionnement des soupapes. La quincaillerie fournie par l’installateur doit etre appropriee pour la construction des murs. Les dispositifs d’ancrage murauxdoivent avoir un indice d’arrachement minimum de 454 kg (1 000 lbs.). La commande a infrarouge Adaptive® doit etre connectee avec un transformateur 24 V c.a. Classe II. Des connexions a du 110 V c.a. peuvent provoquer des blessures personnelles et endommager lescomposants electroniques. Les garanties du produit figurent sous la rubrique « Informations techniques » sur notre site Internet a .IMPORTANTE! Lea todo este manual para garantizar su instalacion adecuada. Cuando haya terminado la instalacion, presentelo al duenoo al Departamento de Mantenimiento. Separe las piezas del empaque y asegurese de que no falte ninguna antes de desechar el material del empaque. Si falta alguna pieza, no comience con la instalacion hasta que obtenga las faltantes. Asegurese de que todas las tuberias de suministro de agua hayan sido lavadas ycerradas completamente antes de comenzar la instalacion. Los desechos en las tuberias de suministro pueden causar averias en lasvalvulas. Las piezas metalicas proporcionadas por el instalador deben ser adecuadas para la construccion en la pared. Las sujeciones depared usadas deben tener una capacidad minima de extraccion de 454 kg (1.000 libras). El control infrarrojo Adaptive® debeconectarse con un transformador clase II de 24 V CA. Las conexiones a 110 V CA pueden causar lesiones personales y producirandanos a los componentes electronicos. Se pueden encontrar garantias de los productos en Product Information (Informacion sobre productos) en nuestrositio Web en ADA COMPLIANT TDB3108 with Infrared Control TDB3108 avec commande a infrarouge Modelo TDB3108 con control infrarrojo TDB3108 Juvenile with Infrared Control TDB3108 Enfant avec commande a infrarouge Modelo infantil TDB3108 con control infrarrojo WF3208 with Infrared Control WF3208 avec commande a infrarouge Modelo WF3208 con control infrarrojo TDB3108 TAS Height with Infrared Control TDB3108 Hauteur TAS avec commande a infrarouge Altura TAS del modelo TDB3108 con control infrarrojo 215-1187 Rev N; EN 06-915B © 2007 Bradley Corporation Page 1 of 85 4/6/2007 IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with theinstallation, file this manual with the owner or maintenance department. Separate parts from packaging and make sure all parts are accounted for beforediscarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Make sure that all water supply lines havebeen flushed and then completely turned off before beginning installation. Debris in supply lines can cause valves tomalfunction. Hardware supplied by installer must be appropriate for wall construction. Wall anchors used must have a minimum pull-outrating of 1,000 lbs. The Adaptive® Infrared control must be connected with a 24 VAC Class II transformer. Connections to 110 VAC can cause personal injury and will result in damage to the electronics. Product warranties may be found under “Product Information” on our web site at IMPORTANT ! Lire ce manuel d’insta...