Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. WARNINGFOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Canada United States GENERAL INFORMATION: The Warm & Serve Drawer IMPORTANT: The warmer drawer must be installed on can be used as a stand alone appliance or combine with a a leveled surface from left to right, rear to front and the built-in oven mounted above. surface must be capable of supporting 100 lbs (45,4 Kg). P/N 318201810 (0901) Rev. E English – pages 1-4 Espanol – paginas 5-8 Francais – pages 9-12 DABFECWarm & Serve Drawer Dimensions Stand Alone Installation Combination Warm & Serve Drawer/ Built-in Oven Installation NOTE: A 60" (152,4 cm) long cable is supplied with the Warm & Serve Drawer. FLOOR Warm and Serve Cutout Warm and Serve Drawer 60" (152,4 cm) Cord Minimum distance to floor 4." (11,4 cm) IMPORTANT: The Warm & Serve Drawer runs off a single phase three-wire 120 volt, 60 hertz, AC only electrical supply with ground. H* = 11 5/8" (29,6cm) Min. is a Critical dimension and has to be respected. Bottom of oven cutout Caution: Two 3" (7,6 cm) wide X 3/4" (1,9 cm) thick planks have to be install and they should be able to support 200 pounds. (90,7 Kg) 29." (74.9cm) Printed in the USA J** = 3" (7,6cm) Max. Electrical Junction Box for wall oven must be lower than the warmer drawer cutout. A. HEIGHT B. WIDTH C. DEPTH 11 ." (28,6 cm) 30" (76,2 cm) 23 3/8" (59,4 cm) D. CUTOUT HEIGHT E. CUTOUT WIDTH F. CUTOUT DEPTH Min. 9 7/8" (25,1 cm) 28 ." (72,4 cm) 24" (61 cm) Max. 10 ." (26 cm) 28 ." (73 cm) A. HEIGHT B. WIDTH C. DEPTH 11 ." (28,6 cm) 30" (76,2 cm) 23 3/8" (59,4 cm) D. CUTOUT HEIGHT E. CUTOUT WIDTH F. CUTOUT DEPTH G. HEIGHT Min. 9 7/8" (25,1 cm) 28 ." (72,4 cm) 24" (61 cm) 1 ." (4,4 cm) Max. 10 ." (26 cm) 28 ." (73 cm) Depends on critical dimension H 1 WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS Important Notes to the Installer 1. Read all instructions contained in these installation instructions before installing appliance. 2. Remove all packing material from appliance before connecting the electrical supply. 3. Observe all governing codes and ordinances. 4. Be sure to leave these instructions with the consumer. Important Note to the Consumer Keep these instructions for future reference. IMPORTANT SAFETY INSTRUCTIONS • Be sure your appliance is installed and plugged into a 120 Volt grounded outlet. • This appliance must be electrically grounded in accordance with the National Electrical Code ANSI/ NFPA No. 70—latest edition in the United States, or CSA C22.1, Part 1 in Canada, and local code requirements. Tools You Will Need Phillips® Screwdriver Pencil Ruler or Tape Measure and Straight-edge Hand Saw or Saber Saw Spirit Level Warm & Serve Drawer Installation 1.Locate the 2 anti-tip brackets supplied as shown on fig. 1. c/c 25 5/16" (64,3 cm) 24" (61 cm) Max. 23 5/8" (60 cm) Min. c/c 12 21/32" (32,2 cm) Figure 1 2.Slide drawer into cutout opening until front frame of drawer is flush against cabinet. Be careful not to pinch electrical cord. 3.Remove the drawer as instructed in the Use & Care Guide and secure drawer housing to cabinet using the 3 nickel-plated screws supplied (see Figure 2). Do not overtighten screws. 4.The 60" (152,4 cm) appliance power cord can now be connected into the 120 Volt outlet. 5.Proceed with mounting built-in oven above the drawer (if applicable). Follow installation instructions provided with built-in oven. Make sure to use anti-tip brackets supplied with the built-in oven. Figure 2 Use screws supplied to attach drawer to front of cabinet. Electrical connection IMPORTANT Please read carefully. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong grounding wall receptacle to minimize the possibility of electric shock hazard from the appliance. The wall receptacle and circuit should be checked by a qualified electrician to make sure the receptacle is properly grounded. Where a standard 2-prong wall receptacle is installed, it is the personal responsibility and obligation of the consumer to have it replaced by a properly grounded 3-prong wall receptacle. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Disconnect electrical supply cord from wall receptacle before servicing cooktop. Preferred Method Grounding type wall receptacle Power supply cord with 3-prong grounding plug. Do not, under any circumstances, cut, remove, or bypass the grounding prong. 2 WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS Model and Serial Number Location The serial plate is located as shown below. When ordering parts for or making inquiries about your Warm & Serve Drawer, always be sure to include the model and serial numbers and a lot number or le...