Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Warning If visible cracks appear in the surface, the appliance must be disconnected from the mains immediately. Spillages of plastics and other meltable materials such as sugar and food containing sugar (also applies to food with a natural sugar content to which no extra sugar has been added), such as marmalade, jam, fruit juice, etc. must be wiped off the ceramic surface while still hot. Failure to do this could cause the griddle to peel and crack. Use the enclosed glass scraper and polish with a ceramic glass cream cleaner afterwards. Any cooking utensils which have been into contact with the above mentioned materials must be cleaned thoroughly before being placed on the ceramic surface. The warranty does not cover damage to the glass ceramic griddle which can be attributed to any of the above events. Cleaning and maintenance For reasons of hygiene and safety, the griddle must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Splashguard The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface” Be aware of the two retaining pegs, which are sharp. 4. Replace the splashguard in position ENSURE that it is fitted the correct way round. Never use hard or sharp implements to lift off the splashguard. Do not wash the splashguard in a dishwasher. The hob must not be used with the splashguard off. Technical data Mains Voltage 230 V Electrical connection 230V - 50Hz Total wattage 1400W This unit is labelled to indicate conformity with the lowvoltage directive (73/23/EEC) and the EMC directive (89/336/EEC). Unpacking #$. ' (. Transport damage )( *. (' ( . % *. * $ . +* % . . . , % '. $. ( '. Electrical connection The electrical connection may only be Stainless steel surfaces 5. Heat the glass griddle until the performed by a qualified electrician/ Perform daily cleaning with a slightly water boils, brushing with a stiff competent person. The electrical damp cloth. For more severe soiling, brush as you do so. connection must be carried out in use a liquid scouring cream. Always 6. Switch off the glass griddle when accordance with prevailing regulations clean the steel in the direction of the the water boils. Continue cleaning for appliances using heavy current. steel finish. To ensure that the steel with the stiff brush. The connection must comply with any retains its shine, it is recommended 7. Allow the glass griddle to cool specific requirements specified by the that you use a polishing agent for (only cool enough so you can local electricity supply authority. stainless steel on a regular basis. touch it). 8. Remove the dirty water with There must be no interference with . Always polish in the direction of the kitchen roll. steel finish (cross-wise). 9. Wipe the surface with a clean, wet any of the unit’s electrical parts. cloth. Never use steel wool, metal sponges or 10. Wipe the surface with a dry cloth. The cable is mounted in the pegs as other abrasive cleaning agents. 11. Apply a thin coat of cooking oil to shown. the glass griddle and rub in. Unscrew the cover while connecting . The ceramic glass griddle the cables. The glass griddle must be cleaned each time it has been used. A unit led directly to the power point or the outlet rose. More units may be connected via one . 1. Pour water onto the glass griddle, or more junction boxes. add a little washing-up liquid, and The cable must be connected via an scrape off as much as possible using external switch with a contact the scraper. Remove the dirty water separation of at least 3 mm in each with kitchen roll. pole. 2. Use the rough side of a scouring sponge to apply more water and Please observe these instructions, detergent (washing-up liquid or otherwise the warranty will not liquid scouring agent) to the glass cover any damage that may occur. surface. Scour thoroughly. 3. Remove the dirty water with kitchen Single-phase zero-earth roll. Cable type 1,5 mm. HO5VV-F. 4. Apply more water and washing-up The cable outside diameter must be liquid, using the rough side of a between 7,5 and 10,5 mm. scouring sponge. Scour thoroughly. Installation Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The appliance unit can be mounted in any type of kitchen with a work top whose thickness is between 28 mm and 40 mm. Clearance The distance between the top side of the work top and the carpentry underneath must be at least 47 mm. Min. 47 mm Fixing Screw the fixing brackets out to such an extent that they can be turned in under the work top. Tighten the brackets on to the work top with an ordinary screwdriver. Cut-out measurements -. -. One rectangular hole is sawn out for the *. */. appliance combination ch...