Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
UNDER-COUNTER INSTALLATION Fig. 2 Your compactor has been designed to require a minimum of space whether free-standing or built-in. Only 12” wide x 20” deep, your compactor is smaller than most on the market. (Fig. 2) To install compactor under counter, use Figure 2 to determine the cutout size. Back up compactor with a 2 x 4 to prevent unit from shifting backwards due to repeated closing of compactor drawer. The power outlet should be installed per electrical code near the center of the opening or unit, and 15” to 18” from the floor. The bag storage compartment allows you to store bags and air fresheners conveniently. The swing open storage compartment door allows easy access to bags, etc. IMPORTANT: Make sure compactor can be easily removed (slid out) from under counter in case service is ever necessary. DO NOT fasten compactor to cabinets, countertop, or floor. Do not install flooring material after compactor is placed under the counter of the flooring may later interfere with the compactor being able to be removed from under counter. Fig. 3 REMOVE SCREW 3-4 FT. WIRE CLAMP For free-standing unit, remove wire clamp to obtain additional cord length if necessary. (Fig. 3) Remove top right back panel screw, slip wire clamp off cord, and replace screw. WHAT YOUR COMPACTOR DOES Your compactor compresses household trash up to 1/12 of its original volume. The compactor will take normal household trash including milk cartons, glass and plastic bottles, containers and jars, tin cans, wrappings, boxes, food wastes, etc. HOW YOUR COMPACTOR WORKS When you start the compactor, an electrically powered ram moves down into the compactor drawer, compresses the trash and then returns to the “UP” position and shuts off automatically. NOTE: The ram travels about 2/3 of the way down into the container. Because of this, the container must be at least 1/3 full before you notice any compressing. KEY LOCK SWITCH The key lock switch on your compactor is provided for your protection as a safety measure. When the key switch is in the “OFF” position, the compactor will not operate. Lock your compactor, and remove the key for safekeeping to keep children from operating the unit or to prevent anyone from tampering with it. NOTE: Opening the drawer during operation will stop the unit. If the compactor is stopped during its cycle, it will always move back UP when restarted. DRAWER SAFETY LATCH (MODELS 1050L & 1051L ONLY) The drawer latches automatically when closed. To unlatch the drawer, move the lever to the left and pull on the handle. HANDS-FREE DRAWER OPENING (MODELS 1050 & 1051 ONLY) For proper operation, be sure compactor is level. Adjust the level legs as necessary. Quickly depress foot pedal and immediately remove foot. Drawer will open for easy access to trash container. AIR FRESHENER Your Compactor is equipped with Air Freshener Panel, which can hold a solid air freshener, such as a Stick-UP® Air Freshener package. Simply open the air freshener and fasten it to the panel. OPTIONAL CUTTING BOARD KIT (MODEL 1004) You can order an optional cutting board, Model 1004, from your Broan Distributor, or write Broan Mfg. Co., Inc., Hartford, WI 53027. The cutting board rests on the top of the compactor, and features non-marring rubber feet and a gravy groove on the top. To keep your wood cutting board from warping, apply a thin coat of vegetable oil after detergent washing. COLOR MATCHING Your Broan Compactor is equipped with a convenient color matching feature in the door panel. Each compactor (except Model 1052) has one reversible color panel finish in black/almond (Models 1050 & 1050L) or black/white (Models 1051 & 1051L). The main door panel behind the reversible color panel is black. To remove and install the color panel on your compactor: 1. Remove drawer and set it on its back, with the door panels facing up. (See section “DRAWER REMOVAL”, page 7.) For Models 1052, 1050L & 1051L use instructions 6 thru 9 only. Fig. 4 DRAWER PEDAL RETAINER CAP 2. With a commonhead screwdriver pry off the retainer cap on each end of the drawer pedal. (Fig. 4) Fig. 5 3.With a small Phillips head screw- driver or 8 penny nail, push the drawer pedal hinge pin out of one end of the drawer. (Fig. 5) Fig. 6 4 4. Pull the pin completely out of the pedal, and lift the pedal spring out of its notch in the pedal. (Fig. 6) 5. Lift the drawer pedal off of the compactor drawer. TRIM STRIP COLOR PANEL Fig. 7 6. Remove the two screws holding the trim strip to the bottom of the door, and remove the trim strip (Fig. 7) 7. Slide the color panel out. 8. Choose the color you want to show. 9. Slide the color panel back into place, and reinstall the trim strip. Fig. 8 HINGE BRACKET 10. Reinstall pedal by matching it up and sliding hinge pin through one hinge bracket. (Fig. 8) Fig. 9 PEDAL SPRING 11. Use a needle nose pliers to hold the pedal spring, slip it over the end of the hinge pin and slide the pin through. (Fig. 9) Push pin through second hinge bracket and then t...