Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
English 1 Refer to data plate for more information. See "Data Plate" under "Service" for data plate location. Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes. Related Equipment Safety Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material. Never modify or alter the construction of the appliance. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws. CAUTION: For units with glass panels, use care when handling glass to avoid breaking. Broken glass could cause injury. English 2 Installation Before you Begin Tools and Parts Needed Parts Included General Information Power Requirements and Grounding Overall Dimensions • T-20 6-lobe screwdriver • Measuring tape • Drill with bit (1/8") • T-20 6-lobe screws, #8x1/2” (8) Circuit Specifications: 120V, 15A, 60Hz The outlet must be properly grounded in accordance with all applicable codes. A LowHigh_ MedProof+ On/OffDBCE Dimension Model 27” (685 mm) 30” (762 mm) A 25” (634 mm) 28” (710 mm) B 10 3/4” (274 mm) 10 3/4” (274 mm) C 22 1/4” (565 mm) 22 1/4” (565 mm) D 11 7/16” (289 mm) 11 7/16” (289 mm) E 26 5/8” (676 mm) 29 5/8” (752 mm) English 3 Cabinet Cutout Dimensions Instructions are based on standard American cabinets 36” (914 mm) high and 24” (609 mm) deep with a 25” (635 mm) countertop. If using non-standard cabinets, alter dimensions accordingly. Cabinet opening bottom must be able to support 110 pounds (50 kg). 1/2" (12.7mm) 1/2" (12.7mm) Frame Overlaps Cabinet Frame Overlaps Cabinet 1-1/2" (38.1mm) min. to opening above Wall Receptacle Allow 3-1/2" (88.9mm) in front for drawer handle clearance A C D D B Dimension Model 27” (685 mm) 30” (762 mm) A 25 3/8” (645 mm) 28 3/8” (721 mm) B 11 1/8” (283 mm) 11 1/8” (283 mm) C 24” (610 mm) 24” (610 mm) Custom Drawer Front Dimensions Build custom drawer front to the dimensions specified in the following table. All four (Optional) edges must be finished. If using wood, the back must be sealed to prevent moisture damage. A B F D E C G Pilot Holes 1/2" (12.7 mm) Diameter Hole English 4 Dimension Model 27” (685 mm) 30” (762 mm) A 26 3/4” (679 mm) 29 3/4” (755 mm) B 11 1/4” (286 mm) 11 1/4” (286 mm) C 3 5/8” (93 mm) 3 5/8” (93 mm) D 2 3/16” (55 mm) 2 3/16” (55 mm) E 2 5/8” (66 mm) 2 3/4” (69 mm) F 1 5/8” (40 mm) 1 5/8” (40 mm) G 21 1/2” (547 mm) 24 3/8” (618 mm) CAUTION: Installation Procedure Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally. 1. Prepare cabinet cutout. Prepare cabinet cutout and install electrical connection according to the dimensions in “General Information”. 2. Remove drawer. LowHigh_ MedProof+ On/Off 1) Pull drawer to fully open position. 2) Press down right drawer clip. 3) Lift up left drawer clip. 4) Firmly pull the drawer straight out. Retract cabinet rails while drawer is removed. 3. Connect power cord. Insert plug into three-prong, grounded outlet. See “Power Requirements and Grounding” above for electrical specifications. English 5 4. Install warming drawer. CAUTION: It is recommended to have 2 installers to install warming drawer. Failure to do so may result in property damage or personal injury. Slide warming drawer assembly into cutout until it is flush with cabinet. Secure through four screw holes in front frame (drill pilot holes in cabinet first...
Эта инструкция также подходит к моделям:Прочая кухонная техника - WD30JP/01 (887.94 kb)
Прочая кухонная техника - WD30JS/01 (887.94 kb)