Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
9 a. Move the glass away from the spout to prevent drops of beer from falling onto the foam head. Move the glass away from the spout to prevent drops of beer from falling onto the foam head. Move the glass away from the spout to prevent drops of beer from falling onto the foam head. b. Remove the foam that rises beyond the rim of the glass by passing a skimmer over the rim of the glass at an angle of 45°. Your beer is now ready to be Your beer is now ready to Your beer is now ser ved. be ser ved. ready to beser ved. replacing the keg The keg is empty when only foam comes out of the spout and no beer. The display also indicates that the keg is empty. 1 Press the release button to the right to open the doors. Make sure you open the doors fully. 2 Lift the blue locking levers completely. 16 EnglisH 3 Tilt the keg with the assembled tap unit towards you and take it out of the appliance. 4 Press on the release buttons on both sides of the tap unit (1).The tap unit is released from the keg with a click and you can remove it (2). You have to remove the tap unit from the keg before you can replace the tube. Always replace the tube when you install a new keg. Never use a tube for more than 30 days. 5 Hold the tap unit over a sink. 6 Press the blue tube release button to release the tube. 7 Pull the tube connector out of the tap unit and remove the flexible tube out of the tap body. Always clean the tap unit with hot water and, if necessary, some washing- up liquid before you insert a new tube. 8 9 Assemble the tap unit onto the keg (see chapter ‘Preparing for use’, section ‘Placing the tap unit onto the keg’). Insert a new tube into the tap unit (see chapter ‘Preparing for use’, section ‘Placing the tube into the tap unit’). 10 Place the new keg into the appliance (see chapter ‘Preparing for use’, section ‘Placing the keg into the appliance’). EnglisH 17 cleaning Clean the appliance when you replace the keg or when you store the appliance for a longer period. Never use scouring pads, scouring agents or aggressive liquids such as petrol or acetone to clean the appliance. 1 2 3 4 Always unplug the appliance before you clean it. Clean the outside of the appliance with a damp cloth. Remove the spout. Remove and disassemble the drip tray and the drip tray cover. 5 6 You can remove the tap handle by pulling it out of the tap body. Clean the tap unit, the drip tray and the drip tray cover with hot water and, if necessary, some washing-up liquid. Hot water may cause burns. Always check if the water is not too hot before you clean these parts under the tap. Only the drip tray, the drip tray cover and the spout are dishwasher , proof. Environment Do not throw away the appliance with the normal household waste , at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment. Disposal of the cooling element The cooling element inside the appliance contains a substance , that may pollute the environment.Therefore you must remove the cooling element before you discard the appliance. You can also take or send the appliance to a Philips ser vice centre.The staff of this centre will remove the cooling element for you and will dispose of it in an environmentally safe way. Only remove the cooling element when you discard the appliance! 18 EnglisH Be careful of the paste on the cooling element and adjacent parts. If this paste ends up on your clothes, it causes a permanent stain. Remove the cooling element in the following way: 1 2 ,3 4 Unplug the appliance. Slide the release button to the right to open the doors. There are two holes near the hinges of the doors on either side. Remove the four screws located in these holes with a screwdriver. Remove the back cover from the appliance. 5 Pull the cooling fan out of the appliance. Now you see an aluminium plate with fins on it and with two screw , holes. 6 Undo the screws with a screwdriver. , Remove the aluminium plate. After you have removed the aluminium plate, you see a white plate of approx. 4 x 4cm.This is the actual cooling element. 8 Place the flat blade of a screwdriver behind the cooling element. Twist the screwdriver to pry the cooling element off the back of the aluminium plate. 9 Cut the wires attached to the cooling element. 7 Do not connect the appliance to the mains again after you have removed the cooling element. Never reassemble the cooling element once you have removed it. EnglisH 19 10 Hand in the cooling element at an official collection point for chemical waste. guarantee & service If you need information or if you have a problem, contact us online at or call the PerfectDraft call centre. Their phone number is 078-250159 (Belgium), 01801-324000 (Germany) or 0900-2224222 (Netherlands). When you take the appliance to your dealer or a Philips ser vice centre for determination of the cause of the problem, also bring the tube and the keg. guarantee restrictions Your guarantee becom...
Эта инструкция также подходит к моделям:Прочая кухонная техника - HD3620/20 (2.37 mb)