Оценок - 2, средний балл: 4 ( )

Производитель: Hoshizaki Размер: 360.63 kb Название файла: Язык инструкции:

4) Remove any packing from the snout assembly. 5) Apply the gasket (included) to the perimeter of the snout assembly where it mates with the ice bin. 6) Position the snout assembly onto the bin by first placing the bottom of the assembly into the lower hole on the bin's front panel and then rotating the top towards the bin. 7) Install the four screws (included) along the top of the snout assembly. 8) Clean and wipe the interior of the bin and snout assembly with a clean cloth. Fig. 1 Snout Assembly 9 2. Installing the Icemaker 1) Unpack the icemaker, and remove all shipping cartons, tape(s) and packaging. 2) Refer to the charts below and also to the "SET UP" instructions on the icemaker when installing the icemaker. 3) Apply the gasket (included) to the top of the bin and around the perimeter where the icemaker will be installed. Each corner should be mitered and sealed with food-grade silicone. 4) Use the adjustable legs to level the ice bin in both the left-to-right and front-to-rear directions. Single Icemaker Unit 22" WIDE UNIT 30" WIDE UNIT (except KML & KMD) 30" WIDE UNIT (KML only) 42" WIDE UNIT 48" WIDE UNIT B-1150SS B-1300SS Top Kit 48" UNIVERSAL 48" UNIVERSAL 48" UNIVERSAL 48" UNIVERSAL 48" UNIVERSAL Unit Position 7" 1" 3" Cover (3A3198-01) YES NO NO NO NO Top Kit N/A 60" UNIVERSAL 60" UNIVERSAL N/A 60" UNIVERSAL * * 1" B-1500SS B-1650SS Unit Position N/A N/A Cover (3A3198-01) N/A YES (QTY 2) YES (QTY 2) N/A YES * One 30" wide unit on a B-1500SS or B-1650SS requires two covers (HS-2111). Dual Icemaker Units Two 22" WIDE UNITS Two 30" WIDE UNITS (except KML, KMD & KM-900) Two 30" WIDE UNITS (KML only) Two 30" WIDE UNITS (KMD only) B-1150SS B-1300SS Top Kit N/A N/A N/A N/A Unit Position N/A N/A N/A N/A Cover N/A N/A N/A N/A B-1500SS B-1650SS Top Kit 60" UNIVERSAL 60" UNIVERSAL 60" UNIVERSAL 60" UNIVERSAL Unit Position 4.5" 3" 1" 3" Cover (3A3198-01) YES YES YES YES 10 D. Drain Connections See Fig. 3 • A drain outlet, 1" female thread, is located on the bottom of the ice bin. • The drain must have a 1/4" fall per foot on horizontal runs to get a good flow. • The ice bin drain connection must be made separately from the icemaker drains. See the "WATER SUPPLY AND DRAIN CONNECTIONS" instructions on the icemaker. • A plumbing permit and services of a licensed plumber may be required in some areas. Fig. 3 11 E. Final Check List 1) Is the icemaker/ice bin level? 2) Is the icemaker/ice bin in a site where the ambient temperature is within +45°F to +100°F all year around? (Avoid sites with direct sunlight.) 3) Is there at least 6" clearance around the icemaker/ice bin for easy maintenance and service, and for good ventilation? 4) Have the shipping carton, all tape(s) and packing been removed? 5) Are all components, fasteners and thumbscrews securely in place? 6) Have all piping connections been made? 7) Has the ice bin been cleaned and wiped with a clean cloth? 8) Has the end user been given the instruction manual and instructed on the operation and use of the icemaker/ice bin and the importance of the recommended periodic maintenance? 9) Has the end user been given the name and telephone number of the contracted service representative? 10) Has the warranty tag been filled out and forwarded to the factory for warranty registration? 12 III. Operating Instructions See Fig. 4 A. Baffle The baffle prevents ice in the bin from flowing out onto the floor while the bin door is open. 1. Removal 1) Rotate the back edge of the baffle up about 6 inches (15 cm). 2) Pull the baffle forward. 3) Raise the baffle up to remove. 2. Installation 1) Place the baffle into the bin through the snout. Raise the baffle up and engage the two holes on the front edge ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: