Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
4. Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel. 5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve. 6. Replace lower access panel and screws. 7. Drain water from water pan by removing the drain cap. 8. If the room temperature will drop below 32°F (0°C), water must be removed from the drain line. For ice makers with a drain pump installed: ¦ Plug in ice maker or reconnect power. ¦ Turn ice maker off and remove all remaining ice from ice bin. ¦ Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the unit stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump. ¦ Unplug ice maker or disconnect power. 9. Before using again, clean the ice maker and storage bin. 10. Plug into a grounded 3 prong outlet. NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine. TROUBLESHOOTING First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call. In the U.S.A., Ice Maker Operation Your ice maker will not operate WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. ¦ Is the power cord plugged in? Plug into a grounded 3 prong outlet. ¦ Is the control set to ON? Be sure that the control is set to ON. ¦ Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. ¦ Is the room temperature cooler than normal? Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room temperature and shut off even though the bin is not full of ice. Also, unit may not restart once it does shut off. ¦ Does the green light come on when the Clean button is pushed? The ice maker is receiving power but may need cleaning. See “Cleaning.” ¦ Does the ice maker have a drain pump? If there was a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If there is still water in the bin, check to see whether the drain hose is kinked. In Canada, Ice maker seems noisy ¦ Is water being circulated through the ice maker? This is normal operation. Water is added once per ice-making cycle. ¦ Is the water in the reservoir overflowing? This is normal. This overflow helps to purge minerals that were removed from the water during the ice making process. ¦ Is there a “whooshing” sound? Check the following things: ¦ Make sure that the water supply is hooked up and turned on. ¦ Make sure that the drain cap is tight and the water drain pan pump is securely attached to the water pan. ¦ Is there ice between the evaporator plate and the cutting grid? Check that the ice maker is level. See “Leveling.” If the ice maker is level, and the problem persists, run a cleaning cycle. See “Cleaning.” Ice Production Ice maker runs but produces no ice ¦ Is the control set to ON? Be sure that the control is set to ON. ¦ Is the water supply connected? Make sure the water supply is properly connected and turned on. ¦ Is the drain cap securely in place? If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap. ¦ Is there debris in the drain tube? Clean the drain tube. ¦ Is there a kink in the drain line? Be sure that there are no kinks in the line. ¦ Is the service light flashing on and off continually? Call for service. Ice maker runs but produces very little ice ¦ Is the room temperature hotter than normal? Room temperatures of more than 90°F (32°C) will normally reduce ice production. WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. ¦ Is the condenser dirty? Dirt or lint may be blocking the airflow through the condenser. See “Condenser” in the “Cleaning” section. ¦ Is there scale buildup in the ice maker? If there is white scale buildup in the ice maker’s water or freezing system, you should clean the ice maker. See “Interior Components” in the “Cleaning” section. ¦ Is the drain cap securely in place? If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap if it is loose. Grid is not cutting ice sheets ¦ Is the cutter grid securely in place? Check the cutter grid harness plug to make sure the connection is intact. See “Interior ...
Эта инструкция также подходит к моделям:Прочая кухонная техника - MIM1554WRS (1.07 mb)
Прочая кухонная техника - W10206510A (1.07 mb)