Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Using silicone sealant, place a bead of sealant onto the top edges of the area on the adapter where the ice machine will go. Install the ice machine onto the dispenser, center the machine left to right and align the machine flush to the back. Install the thermostatic bin control cap tube into the thermal well mounted in the bin. Note: The thermostatic bin control kit is required on all ICE Series Cubers. Fasten together at the back of the machine using fasteners from the icemaker and mounting hardware from the kit. Place the front cover plate onto the dispenser in front of the ice machine. Follow the ice machine start-up instructions included with the ice machine. Completion Make a final check for any leaks and correct as necessary. Reinstall the splash panel and secure it with two Phillips head screws. Check for proper operation of the dispense system. Instruct the site manager regarding the requirements for maintaining, operation and sanitizing the dispenser. The dispenser must be cleaned and sanitized periodically as prescribed by local health authority or the product supplier, which ever has jurisdiction. Ice-O-Matic recommends the dispenser be cleaned and sanitized at least monthly if not specified by local code requirement. Dispenser Cleaning and Sanitizing Procedures WARNING: When using cleaning fluids or any chemicals, rubber gloves and eye protection should be worn. The sink, grill and splash panel should be cleaned daily. The ice storage system should be sanitized monthly. Daily: Lift up and remove the grill from the sink. Use soap, hot water and a clean cloth to wash the sink and splash panel: rinse with hot water, allowing plenty of hot water to run down the drain. Wash the grill, then rinse with clean water. Place the grill back in sink. Clean all exterior surfaces of the unit with warm water and a sponge. Rinse out the sponge with clean water, wring excess water out of the sponge, and wipe off external surfaces of the unit. Wipe unit dry with a clean soft cloth. Do not use abrasive type cleaners. Monthly And Initial Start-Up: Sanitize the ice storage system Disconnect power to the dispenser and ice machine. Remove the dispenser front cover plate in front of the ice machine and discard all remaining ice, Mix a solution of 1 ounce of household bleach to 2 gallons of potable water, or: mix a solution of any approved sanitizer, following the directions for mixing and applying that sanitizer. Unscrew the sweep arm from the rotor shaft, and pull the rotor from the hopper. Using a clean cloth or sponge, wipe all interior surfaces of the storage hopper with the sanitizing solution, allow to air dry. Wipe all surfaces of the rotor and sweep arm with the sanitizing solution, allow to air dry. Lift up & out and remove the upper front panel. Twist the clear ice chute 1/3 turn and pull down to remove. Locate the two thumbscrews holding the upper ice chute and remove them. Remove the upper ice chute from the machine. Thoroughly wipe the surfaces of the bin door and both ice chutes with the sanitizing solution, and allow to air dry. Place the upper ice chute back into the dispenser and secure with the thumb screws. Place the clear ice chute back into the dispenser and replace the upper front panel. Reassemble the rotor and sweep arm assembly and replace the dispenser cover plate. Reconnect power to the ice machine and dispenser. Service Diagnosis PROBLEM PROBABLE CAUSE CORRECTION Will not dispense No ice in hopper Fill bin with ice ice Vend switch does not close Check vend switch, replace if open Drive motor not working Check drive motor, replace if not working Door solenoid will not open door Check/replace door and solenoid Rotor will not turn Check hub of rotor Relay for vend switch does not Check relays, replace as required close during operation Electrical Sequence Reference Wiring Diagram, Page 20-21 Ice Vending Ice is dispensed as long as the vend lever or push button is depressed or until the bin is empty. When the ice vend lever or push button is depressed, the vend switch closes, and makes a circuit to the coil of relay A. When relay A is energized, relay A’s contacts 4-6 and 5-3 close. Relays A’s contacts 5-1 open When relay A’s contacts 4-6 close, they make a circuit to the door solenoid, which opens the ice door. When relays A’s contacts 5-3 close, they make a circuit to the coil of relay B. When relays A’s contacts 5-1 open, the circuit to the timer is opened. When relay B’s coil is energized, it closes a circuit to the gearmotor, and the gearmotor turns the rotor. Agitation Relay A’s contacts 5-1 are closed and make a circuit to the timer. The timer is energized when the unit is not dispensing. The timer switch will close for a few seconds every two hours. When the timer switch is closed, it makes a circuit to relay B’s coil. When relay B is energized, it powers the gearmotor and the rotor is turned. This parts list contains the service parts available for the IOD16022 and IOS22030 ice only dis...
Эта инструкция также подходит к моделям:Прочая кухонная техника - Counter Top Dispenser IOD16022 (1.84 mb)