Оценок - , средний балл: ( )

Инструкция по эксплуатации Haier, модель HPIM26W

Производитель: Haier
Размер: 450.2 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

2. The icemaking cycle begins when the evaporator rods are dipped into the water box. You will hear the compressor working. 3. It will take approximately 6-12 minutes for each icemaking cycle, depending on the size selected. The larger the size, the more time is needed to make the ice. After the cycle is finished, the water box will tilt forward and the remaining water will flow back into the water storage tank. The evaporator rods will then release the ice cubes. Note: If the room ambient temperature is below 60. F, then small or medium ice cube sizes are suggested to prevent ice cubes from fusing together. 4. Approximately 60 seconds later, the water box will tilt backwards and the ice pusher will push the ice into the ice storage basket. After the water box flips back to its original position, the next icemaking cycle will begin. 5. When the maximum capacity of ice cubes is collected and the ice reaches the temperature sensor, the icemaker will automatically stop operating. The “ICE FULL” LED indicator will light up. If more ice is needed, remove the ice from the ice storage basket; then replace the basket into the machine, making sure that the basket is placed back to its original position. Note: When replacing the basket, ensure that the temperature sensor is above the basket so that the machine operates properly. 6. To continue making ice, check that there is water in the water storage tank. If there is no water in the water storage tank, then no water will be pumped into the water box, and the operation will stop. The "Add Water" LED display will light up. Press the “OFF” button. Fill the water storage tank with water, and then press the “ON” button for the icemaker to begin operating again. Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting. 7. If the compressor stops for any reason such as water shortage, too WARNING much ice, power off, etc., do not restart the machine right away. Wait at least 3 minutes before restarting the machine. English ClEANING AND MAINTENANCE Before using your icemaker, it is strongly recommended that you clean the icemaker thoroughly. Be sure to clean the icemaker regularly. 1. When cleaning, please make sure the power has been turned off and the plug is disconnected from the outlet. When plugging or unplugging the unit from the outlet, pull directly on the plug. Never pull on the power cord. 2. Remove the ice storage basket. 3. Drain remaining water from unit. Remove the cap, then the rubber plug from the spout. When assembling back together, the rubber plug must be inserted first into the spout, and then capped. Otherwise, the icemaker will leak. 4. Use a mild detergent diluted in warm water and wipe with a soft towel or sponge. Solvents, detergents and abrasives must never be used for cleaning. WARNING 5. Wipe the inner parts, such as the ice storage basket, water reservoir, water box, ice pusher, and evaporator rods. 6. The outside of the icemaker should be cleaned regularly with a mild detergent solution, warm water, and a soft cloth. 7. Dry the interior and exterior with a soft cloth. 8. To begin making ice once the unit has been cleaned, pour clean water into the water reservoir and fill up to the level line follow operating instructions. Never tilt or place the icemaker on its side, otherwise you must wait 10 hours for compressor coolant to settle. WARNING 9. To ensure the cleanliness of the ice cubes, the water in the water storage tank should be replaced every 24 hours. 10. When the machine is not in use or will not be used for an extended period of time, unscrew the drain cap, then remove the rubber plug behind the unit to empty the remaining water in the water reservoir completely. (Follow the instructions in number 4 above.) Drain Cap Drain Spout Rubber Plug Drain Spout 10 English TROUblEShOOTING GUIDE Problem Possible Causes Solution “ADD WATER” indicator light turns on. Low water level or lack of water. Add water and the icemaker will operate automatically. There is no indication on the control panel. Disconnection of plug. Check that the plug is plugged into the electrical outlet. “Ice Full” and “Add Water” indicators light up simultaneously. Electrical Power Surge or There may be air in the lines or the lines are blocked. The water tank cannot detect water level. Turn off the icemaker, pull out the electric plug, fill it with water if needed, replace the plug and then restart the unit. or Inspect relative parts; remove the drain cap on the back of the unit and drain out a small amount of water. Replace the drain cap and attempt to use the unit again. or Check if ice is blocking the ice pusher. Turn off the unit; let the ice melt and restart. Otherwise, call Haier America Customer Service. The “Ice Full” indicator light is on. The ice basket is full. Remove ice from the ice storage basket to make more. The unit does not operate. Power is not being supplied to the unit. The ambient temperature or the water temperature...