Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
LO WATER: 1. There is a sensor in the water reservoir that reaches down to the very bottom. The machine will not start if water is not present at this sensor. 2. A hard error will occur should water not be present within 60 seconds of power up or if the sensors are disconnected or damaged. Relay output indication: Each relay on the board has an indicator light associated with its output. For example, when the relay for the water feed solenoid is energized, the adjacent indicator light glows green. Comp/Sol output: The output for the compressor is labeled COMP/SOL. 15 Wiring diagram 16 801 CHURCH LANEEASTON, PA 18040, USA800-523-9361 OR 610-252-7301FOR SERVICE CALL: ON THE WEB: LELE 2LOWNORM 6HIGHNORM LE3COM LE4ALARM LE LOW 7LE 8CLOG DRAINCOM WATER LEVELOUT (light on) -V (3 WIRE) +V RETURN(CONTACT CLOSURE) BINFULL S3CLEAN MOM S2PURGE MAINT OR INPUT 2 1234 J51RED / GRAY PAIR GRAY / GRAY PAIR J24 J22J23 CONTROL PC BOARD J21 JUMPER PURGE (Y) POWER (G) LOW BIN (G) AUGER ON (G) REFRIG ON (G) CLEANING (Y) SERVICE (R) HI AMPS (R) HI PRESS (R) LO PRESS (R) DRAIN CLOG (R) TIME DELAY (Y) LO WATER (R) CPU (G) HI WATER (R) SWITCH RESET J34J33J32J31 1y/230Vac SIGNALRETURN2 J3 GRAY / GRAY PAIR HIPRESSHIGH PRESSUREOPENS @ EXCESSP 2PE OPEN @ 425 PSICLOSE @ 295 PSI K1CNO L1 J7J4J5 MOTORFAN J17 J18 J2 BRNBLU 123 J50 .6 Amp Max1/2hp Max NOCK3 J6 M2M1 #2 #12 #9 #1#3 GRN #34 CB1 COMPSOLFAN DRV #19#18 SNUBBER 20FLA240Vac CONTACTOR K10 L2 L1 25 #7#8 S1O I240Vac / 20FLA ON/OFF SWITCH 14 ~11Amp DRAW RUNNING 50/60Hz208V/230Vac #28 #13 #14 #15 #16 #17 #26#27#25 P1 K11 C2 START C1 RUN COMP>.50hp SRC 6 41 25 #10 J10J9 L2 J11 J12J8 #11 #31#30#33#32 FCV- 1 FCV-2 230Vac 20Watt 20Watt230VacDRAIN INPUTWATER J16 J13 J14 J15 H2OIN POTENTIALRELAY H2ODRN TP11 TP4 TP7 TP8 TP6TP5TP3 BLUBRNGRN AMPSENSINGD9D5D10 D6 D15 BLUBLKBRN P52 J52 L2GNDL1 BRNBLU 1 1111 Compressor data Compressor current draw at 230 VAC Air-cooled Ambient air temp. 60°F/16°C 70°F/21°C 80°F/27°C 90°F/32°C 100°F/38°C 7.1 7.5 7.8 7.8 8.1 Water-cooled Condenser water temp 50°F/10°C 60°F/16°C 70°F/21°C 80°F/27°C 90°F/32°C 7.0 7.0 7.4 6.7 8.0 Locked rotor amps 54 Gearmotor data Brother Gearmotor current 2.8A (nominal) Locked rotor amps 15 amps Resistance of windings 208-230 vac gearmotor (Brother) 6.2. Compressor start winding 3.0. Compressor run winding 1.4. Fan motor 38. 17 18 Mechanical system Evaporator disassembly 1. Press PURGE button to purge evaporator, and then turn power OFF. 2. Unscrew and remove stream divider as shown. 3. Unplug and remove gearmotor as shown. 4. Remove all traces of petrol-gel from the auger shaft. Fig. 13 Fig. 14 Fig. 15 5. Unscrew and disconnect transport tube from louvered docking assembly. 6. Unplug sensor at the electrical box. 7. Remove vent tube from shuttle housing as shown. 19 Fig. 16 8. Loosen nut on V-band clamp and remove. 9. Remove V-band clamp from front of evaporator. 10. Remove main housing as shown. Fig. 17 11. Remove and discard mating ring and seal. 12. Carefully remove auger. 20 Lube with soap touch Do not Cardboard disc Fig. 19 3. Press new mating ring into main housing as shown. 4. Lube the shaft with liquid soap in the area shown and slip on seal and spring. Note: Do not touch the sealing surfaces. Use cardboard disk to install. Fig. 20 5. Reinstall main housing as shown. Evaporator reassembly Fig. 18 1. Remove and inspect O ring seal. Discard if damaged in any way. 2. Clean O ring groove. Lubricate O ring with petrol-gel and reinstall. 21 Fig. 22 11. Reconnect transport tube to louvered docking assembly. 12. Plug sensor in at the electrical box. 13. Reconnect vent tube to the shuttle housing as shown. Apply petrol-gel Fig. 23 14. Apply a coat of petrol-gel to the auger shaft. 15. Install gearmotor, making sure that insulation is properly seated between gearmotor and main housing as shown. 16. Firmly tighten four gearmotor bolts in place. removed for clarity Note: Shuttle housing Fig. 21 6. Orient auger shaft with keyway in the upward position. 7. Force main housing into position against evaporator and place 1/4" (7mm) diameter Phillips screwdriver into hole in the auger shaft. 8. Replace V-band clamp as shown. 9. Replace nut on V-band clamp and tighten. 10. Remove screwdriver. 22 Fig. 25 20. Remove bolt and reinstall the washer and bolt. Place retainer over bolt and secure with nut and washer. Apply petrol-gel Fig. 26 21. Lubricate body of stream divider with petrol-gel and reinstall. 22. Plug gearmotor power cord into electrical box. Fig. 24 17. Insert a bolt into the auger shaft and finger tighten. 18. Using a wrench, rotate the shaft clockwise to align the keyways in the gear housing and the shaft so as to accept the key. 19. Insert the key into the keyway. 23 High pressure vapor high side refrigeration line run filter dryer thermostatic expansion valve high side service port low side service port condenser heat exchanger low side refrigeration line run compressor High pressure liquid Low pressure liquid Low ...
Эта инструкция также подходит к моделям:Прочая кухонная техника - HCC1000A (3.18 mb)