Оценок - 3, средний балл: 3.7 ( )

Производитель: Follett Размер: 1.85 mb Название файла: Язык инструкции:

Do not operate with front cover removed. Hot parts. Do not operate with cover removed. To reduce risk of shock disconnect power before servicing. Most ice machine cleaners contain citric or phosphoric acid, which can cause skin irritation. Read caution label on product and follow instructions carefully. Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition. Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice. 4 Specifications Electrical Each icemaker and dispenser require a separate circuit with electrical disconnect within 10 ft (6m). Equipment ground required. Standard electrical – 115V, 60Hz, 1 phase. Maximum dispenser fuse – 15 amps, Maximum icemaker fuse – 20 amps each Maximum icemaker amperage – 11 amps each Cord and plug provided on icemaker and dispenser Electrical connections Model Electrical connection Circuits required 25FB400A/W, 50FB400A/W, 110FB400A/W cord & plug provided 115/60/1, 20 amp max. fuse size 25CT400A/W, 50CT400A/W, 110CT400A/W cord & plug provided 115/60/1, 20 amp max. fuse size 25CR400A/W, 50CR400A/W, 110CR400A/W dispenser, icemaker and bin signal: cord & plug provided 115/60/1, (2) circuits required dispenser: 15 amp max. fuse size icemaker: 20 amp max. fuse size VU155R400A/W, VU300R400A/W VU155BR400A/W, VU300BR400A/W VU155R400A/WX, VU155BR400A/WX dispenser, icemaker and bin signal: cord & plug provided 115/60/1, (2) circuits required dispenser: 15 amp max. fuse size icemaker: 20 amp max. fuse size VU155NR400A/W, UD300R400A/W VU155R800A/W, VU300R800A/W, VU155R800A/WX, VU155BR800A/W, VU300BR800A/W, VU155R800A/WX dispenser, icemaker and bin signal: cord & plug provided 115/60/1, (3) circuits required dispenser: 15 amp max. fuse size (2) icemakers: 20 amps max. fuse size each Plumbing 3/8" OD push-in water inlet 3/4" MPT drain 3/8" FPT condenser inlet (water-cooled condenser only) 3/8" FPT condenser drain (water-cooled condenser only) Notes: Slope to drain of 1/4" per foot (6mm per 30.4cm run) with a 1/2" min. is recommended. Water shut-off recommended within 10 feet (3m), drain to be hard piped and insulated. Separate drains for icemaker and condenser. To prevent back flow, do NOT connect drains. Follett recommends installation of an activated carbon filter in icemaker inlet water line. Ambient Air temperature 100° F/38° C max. 50°F/10°C min. (best performance below 80°F/27°C) Water temperature 90°F/32°C max. 40°F/4°C min. (best performance below 70°F/21°C) Water pressure 70 P.S.I max. (482 kPA) 10 P.S.I. min. (89 kPA) 5 Dimensions and clearances Entire front of icemaker must be clear of obstructions/connections to allow removal. 12" (305mm) clearance above icemaker for service. 6" (153mm) minimum clearance between exhaust side of icemaker and any adjacent equipment. MCD400A & R400A – 18" (457mm) minimum, 10 ft (3m) maximum clearance between discharge and air intake grilles. Front view — air-cooled Back view — air-cooled top mount top mount 13.00" (331mm) 4.875" (124mm) 2.375" (61mm) A A B B F F D E C A B C C Front view — air-cooled Satellite-fill Front view — water-cooled Satellite-fill Back view — water-cooled top mount 12.875" (327mm) 4.75" (121mm) 8.375" (213mm) 2.25" (57mm) (51mm) 6.875" (175mm) 2" 1.875" (48mm) 1.875" (48mm) 7.00" (178mm) Side view — air-cooled and water-cooled Icemaker plug configuration top mount and Satellite-fill NEMA 5-20 22.75" (578mm) 20.75" (527mm) Satellite-fill air-cooled units only 17.00" (432mm) A – 3/4" MPT drain D – 3/8" FPT condenser inlet B – 3/8" OD push-in water inlet E – 3/8" FPT condenser drain C – Electrical cord F – Bin signal cord 6 Installation Icemaker performance is very sensitive to the quality of installation. To ensure proper performance, ease of service and warranty coverage, it is critical that you follow the requirements detailed in this manual. If you cannot meet these requirements or have questions, call our technical service group immediately at (800) 523-9361 or (610) 252-7301. Top mount icemaker on bin installation procedure (models MCD400A/WBT and MFD400A/WBT) Install icemaker and rough-in utilities 1. Install ice storage bin in its final location. 2. Install one supplied grommet in large knockout in base of icemaker and second supplied grommet in ice hole provided in top of ice storage bin. 3. Rough in plumbing and electrical per specs provided. 4. Flush all water lines before final hook up. 5. Position icemaker with utility connections facing rear of bin. A. If new storage bin and icemaker – position icemaker with connections facing rear of bin. B. If using existing bin – place supplied gasket 2.5" (64mm) from front of bin (Fig. 2). Position icemaker with utility connections facing rear of bin. 6. Make final plumbing and electrical connections. 7. Working from inside bin storage area, push end of transport tube without fasteners up through grommets into icemaker, leaving about 2" (51mm) hanging down in bin. 8. Route free end of tube to...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: