Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Do not allow acids (citrus juices, tomato sauces, etc.) to remain on the warming drawer’s surfaces. the finish may stain. • Do not try to remove heavy spills with a sharp object such as a knife or metal spatula. Sharp objects may scratch the surfaces. • always wipe stainless steel surfaces in the direction of the grain. Control Panel Clean the control panel with a soft cloth soaked with a solution of mild detergent and hot water. rinse and dry with a soft cloth. exercise caution to avoid introduction of liquids into the area behind the control panel. Do not use abrasive cleaners or scrubbers. they may permanently damage the finish or scrap off the letters and graphics. Moist • Crisp Control Clean the Moist • Crisp lever with a solution of mild detergent and hot water. rinse and dry with a soft cloth. Drawer Handle Clean the drawer handle with a solution of mild detergent and hot water. rinse and dry with a soft cloth. You may also use Dacor Stainless Steel Cleaner. It is available from your Dacor dealer. use it according to the directions on the package. always wipe stainless steel surfaces in the direction of the grain. Glass Surfaces Clean all glass surfaces with a solution of mild detergent and hot water. You may also use a mild glass cleaner to remove fingerprints or smears. Dry completely with a soft, lint-free cloth. Brass and Chrome Surfaces Clean brass and chrome surfaces with a solution of mild detergent and warm water. rinse, dry and polish with a soft, lint-free cloth. You may also use Dacor Stainless Steel Cleaner. It is available from your Dacor dealer. use it according to the directions on the package. Painted Surfaces for the front face of warming drawers with a painted finish, clean with a solution of mild detergent and hot water. rinse and dry with a soft cloth. Do not use abrasive cleaners or scrubbers. they may permanently damage the finish. Gasket the gasket is located around the edge of the drawer opening, below the control panel. Gently clean the gasket with a solution of mild detergent and hot water. rinse and dry with a soft cloth. the gasket material is soft, so be careful not to crush or damage it. Damaging the gasket will cause a poor heat seal and result in poor warming drawer performance. Drawer Slides the warming drawer has slides positioned on each side of the drawer. they allow the drawer to slide in and out smoothly. remove the drawer from the slides to make cleaning easy or to access the serial number plate. the drawer slides themselves do not require maintenance. Removing the Drawer from the Appliance allow the drawer to cool before attempting to remove it. 1. pull the drawer out to the fully open position. 2. push in on the locking tab on one side as you pull the drawer up. See the facing page. 3. When the drawer comes loose from the slide, repeat the same process on the opposite side. 4. Grip the drawer on both sides and pull it free. 5. for safety, push both drawer slides into the drawer opening. Reinstalling The Drawer 1.pull the drawer slides all the way out of the drawer opening. 2. Gently lower the drawer between the extended slides until it is suspended by them. 3. Slide the back of the drawer mounting brackets under the clips on the slides. See the facing page. 4. push one side of the drawer down onto its locking tab, until the tab locks into place. 5. repeat the same process on the opposite side. 6. Gently open and close the drawer to make sure that it is properly installed. 6 Care and Cleaning push in on tab. pull up on drawer front. push drawer front down until tab locks in place. Slide mounting bracket under clip on slide. Clip on slide Slide Drawer removal Drawer Installation Before You Call for Service Problem Solution Guide PROBLEM MAY BE CAuSED BY WHAT TO DO nothing works. power plug disconnected. Connect plug to a dedicated, grounded, three- prong electrical outlet. timer is not set. Select time duration according to the Operating Instructions section. Warming drawer is not connected to power. plug the warming drawer into a 120 vac, 15 amp, dedicated electrical outlet. tripped circuit breaker or blown fuse. Check the house circuit breaker or fuse for the circuit that supplies power to the warming drawer. Drawer does not slide smoothly or drags. Drawer is incorrectly mounted into slide mechanism. remount drawer into slide, per instructions above. Drawer is over-loaded or the load is unbalanced. reduce the weight to less than 50 pounds. redistribute drawer contents. excessive condensation. Warming drawer not preheated. preheat the warming drawer before each use. Incorrect humidity control setting. Set humidity control to CrIsP to allow moisture to vent. One or more of the indicator lights on the control panel blink on and off (one second on, one second off). the control panel computer has detected an error: #1 - temperature error #2 - Sensor error #3 - Key pad error #4 - Control error try resetting the computer. Disconnect the power cord, wait 20 seconds,...
Эта инструкция также подходит к моделям:Прочая кухонная техника - MRWD30 (457.75 kb)