Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Check to ensure that the appliance is undamaged and that all parts and remnants of the packaging are removed from it. - 2 Technical data Mains voltage: 230-240 V ~ 50Hz Power consumption : 150 W Protection class: II / Recommended operating times: Vacuuming: 15 Seconds Sealing: 5 Seconds After vacuuming and sealing allow a break of 80 seconds before continuing to seal further bags. Description of the appliance q Cutter w Protection strip over the sealing wire e Cover - film compartment r Extractor supports t Sealing wire y Control lamp u Appliance cover i Unlocking device right o Button a Unlocking device left s Bag around the exhaust supports d Lug under the exhaust supports f Clip on the filter box g Seal on the filter box h Selector switch j Clip on the filter cover k Lock for exhaust supports Commissioning . Place the appliance on a non-slip and stable surface. . Insert the power plug into a wall power socket. Inserting the film . Open up the cover to the film compartment e and insert a roll of tube film. . Pull a piece of the film out and close the cover of the film compartment e. Utilisation Cutting the film . Pull out as much film as is required for the moment. . Slide the cutter q all the way to the left. . Lay the pulled out film smoothly over the cover to the film compartment e and pull the film to the rear. . Fixate the film above and below the cutter q with your fingers. Note: Press simultaneously on the two unlocking devices left a and right i and open up the appliance cover u. In this way you can better fixate the film when cutting. - 3 . Slide the cutter q over the film and all the way to the other side. Note: The film will only be cut when you slide the cutter q from left to right! Sealing the film Attention: For sealing use only films made of PE-HD (Polyethylene of high density). Otherwise, the sealing seam will not be tight and the appliance could be damaged. You can recognise films of this type by the inscription "PE-HD" on the packaging. Attention: Do not heat the supplied film, for example in a water- bath or similar. It is construed for temperatures of a maximum of 60°C. . Press simultaneously on the two unlocking devices left a and right i and open up the appliance cover u. . Lay the end of the film tube to be sealed over the sealing wire t. . Place the selector switch h into the position “Seal”. . Then close the appliance cover u. Ensure that the film tube does not slip off of the sealing wire t. . Press down the appliance cover u on the outer sides until it audibly clicks in at left and right. . Press and hold the broad button o with both hands until the control lamp y lights up. Hold the button pressed down until the control lamp goes out. Note: To achieve the best results, press the button o down continuously, applying an even pressure and using both hands. Warning: If the control lamp ydoes not go out after a maximum of 10 seconds, the appliance is defective! Immediately remove the plug from the wall socket. Do not attempt to repair the appliance yourself. In this case, contact Customer Services. . Re-open the appliance cover u, as described above, and remove the film. This is now sealed at one end to a bag. This bag can now be filled and the other end sealed by the same procedure. Warning: Fill the bags in such a way that, under no circumstances, food remnants or fluids can run out of the bag when sealing it and permeate into the appliance. - 4 Vacuuming films When sealing, you can at the same time extract the air from the bag (vacuuming): Warning: Do NOT vacuum bags in which there are liquids. They will permeate into the appliance and damage it. . Place the selector switch h to “Vacuum & Seal”. . Then place the open end of the bag around the extraction supports r. For this you can lift them lightly. Note: The bag opening must sit smoothly on the extraction supports r and on the sealing wire t. If it does not, the extraction supports r can block and fail to function. . Close the appliance cover u and press it down on both sides, until a "click" is heard and the appliance cover u locks in at the sides. Air is now sucked from the bag. . As soon as the air has been sucked from the bag, press and hold the broad button o with both hands, as already described, and seal the bag. Storing the appliance . Do not wrap the power cable around the appliance, use the guides provided on the bottom of the appliance. . Store the appliance where it will be dry and free from dust and particles, so that nothing can lodge in the suction device. Cleaning Attention! First remove the power plug from the wall socket and allow the appliance to cool down completely before cleaning it or placing it into storage. NEVER submerse the appliance in fluids of any kind. Do not permit liquids to permeate into the appliance. You could receive a potentially fatal electric shock. Dismantling and cleaning the filter Should food remnants unintentionally be sucked in when vacuuming, a filter protects the appliance from da...