Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Wibur Curtis Company, модель TCO-308

Производитель: Wibur Curtis Company
Размер: 970.99 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for cleaning underneath. 2. In some areas an approved backflow prevention device may be required between the brewer and the water supply. Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction. CAUTION: CAUTION:CAUTION:CAUTION:CAUTION:CAUTION: Please use this setup procedure before attempting to use this brewer. Failure to follow the instructions can result in injury or the voiding of the warranty. CAUTION: CAUTION:CAUTION:CAUTION:CAUTION: CAUTION: DO NOT connect this brewer to hot water. The inlet valve is not rated for hot water. WARNING TO AVOID SCALDING, Do not remove brewcone while brew light is flashing. BREWING 1. Place filter in brew basket. 2. Slide brew cone into brew INSTRUCTIONS Pour leaf tea into basket. rails. Place tea container under brew cone. 3. Press the BREW button to brew tea. FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO WWW.WILBURCURTIS.COM STEPS TO PROGRAMMING WARNING These steps involve working with hot water. Scalding may occur if care is not taken against spilling. PROGRAMMING ONLY REQUIRED IF FACTORY SETTINGS MUST BE CHANGED Changing the ADS™ System Program Your ADS System features a dynamic memory. In the event of a power loss it will remember ALL program settings. IMPORTANT – Before entering the program mode, allow the unit to reach brewing temperature, then press the BREW button to dispense at least 12 ounces of water. This is to clear any air that may be trapped within the water lines. Brew Temperature – Factory Pre-Set to 204°F Function to set brew temperature, 170° to 210°F. Brew temperature will be indicated by READY-TO-BREW light blinking. CONFIRM/RESET BREW TEMPERATURE - Factory Preset to 204. ENTER THE PROGRAMMING MODE #1: • Press for two seconds, then RELEASE. • will start blinking. Each blink equals 2. F, starting at 170. (max. temp. 210. F or 21 blinks). READY TO BREW • To change Temperature, press and HOLD . . • will start QUICK flashing. Each QUICK flash equals 2. F. After reaching 210., temperature starts over at 170.. READY TO BREW .. RELEASE when the desired temperature is reached. The newly set temperature will now be displayed. To set and exit, press . ENTERING THE PROGRAM MODE #1 For ALL functions you must first enter the programming mode. • Turn OFF the power from the Control Panel by pressing . .. Press and HOLD .. Continue HOLDING and press and RELEASE . until starts blinking; RELEASE. READY TO BREW BREW VOLUME - Factory Preset to Brewer Requirements BREW CYCLE COUNTER For ALL functions you must first enter the programming mode. ..Turn OFF the power from the Control Panel by pressing . .. Press and HOLD and press and RELEASE . .. Continue HOLDING until STOPS blinking; RELEASE. ENTER THE PROGRAM MODE #2 READY TO BREW CHANGE BREW VOLUME - CONCENTRATE ENTER THE PROGRAMMING MODE #1 .. Press and HOLD until hot wat...

Эта инструкция также подходит к моделям:
Прочая кухонная техника - TCTD-35S (970.99 kb)
Прочая кухонная техника - TCTD-35 (970.99 kb)
Прочая кухонная техника - TCO-421 (970.99 kb)
Прочая кухонная техника - TCO-417 (970.99 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории