Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
2 • Installation and Operating Instructions.............. 4 • Adjustments......................................................... 6 • Programming Instructions................................. 8 • Care and Maintenance........................................ 8 • Trouble Shooting Guide..................................... 11 • Parts Identification.......................................…... 15 • Wiring Diagrams................................................ 21 Cecilware sells value... Worldwide 45 -05 20th Avenue, Long Island City, NY 11105 TEL • 718-932-1414 FAX • 718-932-7860 NG95A-A 11/10/04 MECHANICAL SPECIFICATIONS MODEL: WIDTH in DEPTH in HEIGHT in Lb (qty) TANK GAL. BURST CAPACITY LIT DISPLAY AREA (W x H) Sq. in. SHIPPG WEIGHT LB. GB1M-IT 8.5 22 34 8 (1) 2.2 58 (7 x 13) 91 65 GB2M-5.5-IT 8.5 22 34 5.5 (2) 2.2 58 (7 x 13) 91 86 GB3M-5.5-IT 11 22 34 4 (3) 3.2 85 (9. x 13) 123 100 GB3M-5.5-IT S/S 11 22 34 5.5 (3) 3.2 85 (9. x 13) 123 100 GB3M-IT-10 LEFT [11.5”W] 11.5 22 34 10 (1) + 5.5 (2) 4.5 112 (123/8 x 13) 164 110 GB3M-IT-10 RIGHT [11.5”W] 11.5 22 34 10 (1) + 5.5 (2) 4.5 112 (123/8 x 13) 164 110 GB4M-IT 14.125 22 34 5.5 (4) 4.5 112 (123/8 x 13) 164 120 GB5M-IT 17.25 22 34 5.5 (5) 4.5 140 (123/8 x 13) 164 140 ELECTRICAL SPECIFICATIONS Model No. Volts Phase Hz Watts Number of Heaters Amps Receptacle Nema No. Circuit Breaker ALL MODELS 120V 1 60 1.8KW 1 15 5-15R 15A ALL MODELS 120/240V 1 60 3.0KW 1 15 L14-20R** 20A ALL EXPORT MODELS 220V 1 60 3.0KW 1 15 †† 20A GB3M-5.5-IT, GB4M-5.5-IT 120/240V 1 60 6.0KW 2 25 L14-30R** 30A 120V, 1.8 KW, 15A, Nema 5-15R standard on all models; 3.0 KW and 6.0 KW, 120/240V units available ** 120/240V, 3 pole, 4 wire grounding type Twist-Plug Receptacle. For 240V units, Use L6-20R or L6-30R, 2 pole, 3 wire Twist-Plug Receptacle. †† 220V Export Receptacle to be specified where order is placed. See Electrical Data Label attached to the back of the unit for proper voltages, breaker sizes and electrical outlet requirements for each model number listed. See wiring diagram in back of manual, for wiring instructions. UNPACKING INSTRUCTIONS Carefully unpack the GB Machine and inspect immediately for shipping damage. Your GB Machine was shipped in a carton designed to give it maximum protection in normal handling. It was thoroughly inspected before leaving the factory. In case of damage, contact the shipper, not Cecilware. INSTALLATION INSTRUCTIONS Water Inlet Connection: This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction. In addition: 1. A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for cleaning underneath. 2. An approved back flow prevention device, such as a double check valve to be installed between the machine and the water supply. The GB beverage dispenser is equipped with a ." Flare Water Inlet Fitting which is located on the left side in the back of the base. HIGHLY RECOMMENDED: A WATER SHUT-OFF VALVE and A WATER FILTER, preferably a combination Charcoal/Phosphate Filter, to remove odors and inhibit lime and scale build up in the machine. Note: In areas with extremely hard water, a water softener must be installed in order to prevent a malfunctioning of the equipment and in order not to void the warranty. After the machine has been unpacked and placed on a counter, pull out the stainless steel drip tray. It should contain the following: A Set of 4 Adjustable Leveling Legs & Water Inlet Fitting. 2 START-UP PROCEDURE 1. Connect the ." dia. copper waterline to the ." flare water inlet fitting of the valve. 2. Plug the power cord into a proper receptacle. 3. Activate the Power Switch (Toggle Up) located on the right side of the splash panel below the door. The power switch controls all power to the machine including the heater elements. The door display panel will light up and the tank will start filling. The LCD window will display this message briefly “CECILWARE, DISPENSER V#.## “. 4. The LCD window will display this message “Low Water Level”. Allow approximately 3-5 minutes for the tank to fill. If the tank does not fill up within the first 5 minutes an error message will appear in the CD window [SYSTEM ERROR, FILL RESPONSE]. See Definition of Screen and Troubleshooting Guide. 5. The LCD window will display this message “Low Water Temp.” Allow up to 30 minutes for the water to reach a temperature of 190°F. The heat up time will depend on the water inlet temperature, the input voltage and the wattage of the elements in the machine. While the tank is heating up, remove the hoppers, load them with products and reposition them back in the machine. Be sure to reposition the hoppers so that the 1/4” pin slides into the hole of the compartment base. When the machine has reached the proper dispensing temperature, the LCD windowill dispay one of these messages: IF THE RINSE MODE IS ON IF THE RINSE MODE IS OFF PLEASE RINSE OR P...