Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
DENVER, COLORADO 80239 (303) 371-3737 ®Mile High Equipment Company 1983 P/N 9081129-01 January 1987 TWO YEAR PARTS WARRANTY |CE"0“MATIC (*> Mll£ H(GH EQUIPMENT COMPANY 11100 Etft Avenu*. D«W.CO 8023» Phone (303) 3?^ -3T37 TYiX 3&64S3 To the original owner of an ICE-O-MATIC MACHINE. We warranty every Ice-O-Matlc Ice Machine to be free from defects in material and factory workmanship if properly installed, cared for and operated under normal conditions with competent supervision. WITHIN TWO YEARS FROM DATE OF ORIGINAL INSTALLATION WHEN REPORTED ON A WARRANTY CARD RETURNED TO THE FACTORY we will replace, F.O.B. our plant, Denver, CO, or F.O.B. authorized Mile High Equipment Co. Parts Depots, without cost to the customer, that part of any such machine that becomes defective, BUT no part or assembly which has been subject to any alteration or misuse, accident, or is from a machine on which the serial number has been altered or removed. We will also honor warranty for 27 MONTHS from date of shipment whichever period is last to expire, provided in either such case installation of the equipment is reported on warranty card and returned to the factory at the time of installation. After thorough examination, the decision of our Service Department shall be final. Any defective parts to be repaired or replaced must be returned to us, transportation charges prepaid, and they must be properly sealed and tagged. The serial and model number of the machine, and the date of original installation of such machine must be given. We will not, however, assume any responsibility for any expenses (including labor) incurred in the field incidental to the repair or replacement of equipment covered by this warranty. Our obligation hereunder to repair or replace a defective part is the exclusive remedy for breach of this warranty; and we will not be liable for any other damages or claims, including consequential damages. No representative, dealer, distributor or any other person is authorized or permitted to make any other warranty or obligate MILE HIGH EQUIPMENT COMPANY, to any liability not strictly in accordance with this policy. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART. ICE-O-MATIC CD-210 DISPENSER TABLE OF CONTENTS SECTION A: GENERAL INFORMATION Model Numbering System ...............................................A-1— A-2 Foreword ..................................................................... A-3 Machine Photo and Utility Connections........................................A-4 General Description of How the CD-210 Works................................A-5 SECTION B: INSTALLATION Uncrating, Inspection, and Freight Claim Procedures..................... B-1— B-2 Set-up Procedure ............................................................. B-3 SECTION C: OPERATION Cleaning Procedures.......................................................... C-1 SECTION D: SERVICE Service Diagnosis............................................................. D-1 General Wiring Diagram....................................................... D-2 SECTION E: PARTS Parts Ordering and Warranty Procedures...................................... E-1 Parts Section ................................................................. E-2 ICE-PMATTC MODEL NUMBERING SYSTEM '■ J The Model Number fully describes the unit A letter code identifies the model series. A two or three digit number identifies the basic family size and electrical characteristics. A second letter code identifies the type of condenser. Cabinet size is identified by a two digit number. Finish is identified by a letter code. The following examples illustrate how Model Numbers are developed: CUBERS FLAKERS C-8 1 F-A-P-C L Controller Cabinet Finish: P = Painted S= Stainless Steel Condenser type: A = Air W = Water R = Remote Cube size: F = Full Cube H= Half Cube Unit electrical characteristics: 0. 1. 2.......... Sasic family size: 2.4.6, 8.12 Model: C “ Cuber F - 7 5 6-A-3 8 P Cabinet finish; P= Painted S= Stainless Steel Cabinet size: 32. 38. or 48 Condenser type: A = Air W= Water R = Remote Unit electrical characteristics: 0, 1.2......... Basic family size: 25. 35. 60. 75. 100 Model: F - Flaker FP = Flaker with Cold Plate MF = Modular Flaker FC = Flaker Chassis only REMOTE CONDENSORS BINS RC-4D ——— unit electrical characteristics 0 or 8 '-Size: 4,6.8.12 ■ - . — ■ Model: RC = Remote Condenser B•55•P - ■ Cabinet finish: P= Painted S= Stainless Steel ■■ Size: 550 lbs. capacity ' Model: B = Bin FLAKER/DRINK DISPENSER [ )-3 5 0 -) \-3BP-! Number of — Dispensing faucets: 3.4, 5.6 or 7 — Same as F Models — Model: D = Flaker/Drmk Dispenser DISPENSERS DC-9 O-P F D-5 5 0-A-P H D-6 5 O-A-P C D-210 T Model: DC = Counter Top Dispenser ■ FD = Flaker Dispenser HD = Hospital Dispenser ...