Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
2 2 When copying is completed, press the AUDIT CLEAR key. . “...” will appear again in the copy quantity display, indicating the auditing mode. . In the interrupt copy mode (see page 29), press the INTERRUPT key after an interrupt copy run is completed. All previous copier settings will be restored and the previous account number will be active. MAKING COPIES Auditing accounts 13 NORMAL COPYING NORMAL COPYING MAKING COPIES Normal copying This copier has two document input stations –– a reversing single pass feeder (RSPF) for automatic document feeding and an original table for manual handling of bound documents. The RSPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of 15 to 24 lbs. . Be sure to remove any staples or paper clips from the originals. . Damaged or crumpled originals may misfeed in the RSPF. It is recommended that these originals be copied from the original table. . Before placing curled or wavy originals into the document feeder tray, be sure to flatten them. If not, original misfeeds may result. . For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides. In this case the settings for location of margin and image rotation in duplex copying may need to be changed to ensure the images are produced in the desired orientation. See pages 22 and 41. . Special originals such as transparency film and tracing paper should not be fed through the RSPF but should be copied from the original table. . The bypass tray and any tray with non-standard size paper cannot be used in the duplex copy mode. . Paper sizes that can be used in the duplex mode are 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17". . If the offset stack mode is enabled using user program No. 19, each set of copies will be offset from the previous set in the sort and group modes. Stream feeding mode If the stream feeding mode has been enabled using user program No. 4, the RSPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed. While this indicator is blinking, any new originals placed in the RSPF will be fed and copied automatically. See page 51, USER PROGRAMS. Power on Power on 1 1 Turn the power switch on. . It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START key during warm-up. Copying will start after warm-up. . If the copier has been programmed in the auditing mode, the START key indicator will not light up and “...” will appear in the copy quantity display. Enter an assigned 3-digit account number. See page 13. . If an optional printer expansion kit or facsimile expansion kit is installed, when the power is already on and all indicators except the POWER SAVE indicator are off, the copier is in the auto power shutoff mode. Press the START key in this case. See page 58, POWER SAVE MODES. One-sided copies from one-sided originals 1 Ensure that no original is left on the original table. 2 Adjust the original guides to the size of the originals. 3 Set the originals face up in the document feeder tray. l The RSPF indicator will light up. If this indicator does not light up, the originals are not properly set, or the RSPF is not properly closed. 14 NORMAL COPYING . The ORIGINAL SIZE indicator for the detected original size will light up, and the paper tray with the corresponding paper size will be automatically selected. . The auto paper select function can be disabled using user program No. 8. If this function has been disabled, use the TRAY SELECT key to select the desired paper tray. See page 51, USER PROGRAMS. . To copy onto a different size paper, use the TRAY SELECT key to make the selection. . The bypass tray cannot be automatically selected. 4 4 Ensure that the one-sided to one-sided copying mode is selected in the ORIGINAL TO COPY section of the operation panel. . When no indicator in the ORIGINAL TO COPY section is lit, the one-sided to one-sided copying mode is selected. 5 5 Adjust the copy density. . This copier has three exposure modes to choose from — AUTOMATIC, MANUAL, and PHOTO. . Automatic exposure is the standard initial setting for this copier. In this mode, the characteristics of the original are “read” by the exposure system and adjustments are automatically made. This optimizes the contrast of the copied images by reducing the effect of colored or shaded background areas. See page 30 to adjust the automatic exposure level. . For manual density adjustment, press the AUTO/MANUAL/PHOTO key to select MANUAL and adjust with the light ( ) and dark ( ) keys as desired. l For photographs, select PHOTO and then adjust with the light ( ) and dark ( ) keys as desired. . There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for tha...